Bedienungsanleitung Midas M32 (Seite 7 von 61) (Englisch)

658461

Zoom out

Zoom in

Vorherige Seite

1/61

Nächste Seite

7 M32 DIGITAL CONSOLE User Manual

1.2 Channel Strip - Group/BusChannels

(1)

(2)

(3)

(4)

(6)

(7)

(5)

(10)

(11)

(12)

(8)

(9)

(1) FADER FLIP - SENDS ON FADER Button

Press to activate the M32’s Sends on Fader function. This function aids with

the level setting of channels sent to any of the 16 Mix Buses. It is only for

channels assigned to Mix Buses 1-16, and does not work for DCA groups,

main or matrix buses. The Sends on Fader function works in two convenient

ways to cover the most obvious situations in a live environment:

When preparing a monitor mix for a specied musician

• Select the monitor bus (BUS 1-8 or BUS 9-16) that feeds the musician’s

stagemonitor

• Press the Sends on Fader button, which will then ash

• Select one of the three input channel layers (INPUTS 1-16, INPUTS 17-32,

AUX IN / USB or BUS MAST)

• As long as Sends on Fader is active all faders in the input channels section

correspond to the send levels on the selected monitor mix bus.

When checking or editing where a selected input signal

is to be sent

• Select the input channel in the left-hand section

• Press the Sends on Fader button, which will then ash

• Select either bus channel layer (BUS 1-8 or BUS 9-16)

• The bus faders now represent the send levels of the selected input channel.

TIP: Sends on Fader can also be used for conveniently sending Bus or

MainM/C signals to Matrices.

Layer Select Buttons

(2) GROUP DCA 1-8

Press this button to select the Group DCA layer.

A DCA group is a grouping function, made possible by the console’s digital

operation, where individual input channels can be grouped together and

controlled with a single output fader on the right-hand side of the console.

Unlike the traditional sub-grouping function found on analogue consoles,

a DCA group does not combine the dierent input channels into a common

sub-mix. Instead, the individual input channels still retain their original

routing characteristics, but their level adjustments are commonly controlled.

(3) BUS 1-8 / 9-16

Press one of these buttons to select either the Bus 1-8 layer or the

Bus9-16layer.

(4) MTX 1-6 / MAIN C

Press to select the Aux In / USB channel layer.

Individual Channel Strip Controls

Each of the above layers operates in a similar way by use of the

followingcontrols:

(6) SEL Button

Press to select a DCA or bus (depending on which layer is active) and allow it

to be edited by the Channel Strip and Main Display.

(8) Channel Meter

This displays the signal level of the DCA or bus, depending on which layer

is active. The PRE LED lights to indicate that the bus is sourced pre-fader,

whilethe COMP LED lights to indicate that compression is active.

(10) SOLO Button

Press to send the channel to the solo bus.

(11) Scribble Strip

Information such as channel number, input source and a graphic icon are

displayed here.

(12) MUTE Button

Press to mute the channel.

(5) Fader

Use the MIDAS PRO Fader to adjust the channel volume or bus sends in Sends

on Faders mode. The faders will automatically display the current status as

layers and functions are changed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midas M32 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info