Bedienungsanleitung Midland BT City 2013 (Seite 5 von 9) (Englisch)

543239

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Intercom

The Intercom feature can be enabled in two ways:

Manual activation:

› Press “Control” button, on one of the two units. Communication is

enabled and remains active until you press the “Control” button

again. You will hear 1 audio tone when the Intercom feature is

enabled and 2 audio tones when it is disabled.

Voice activation (VOX):

› This is enabled by default. To start an Intercom communication,

simply start talking. The communication will remain active for all

the time you are talking.

› If there is no conversation, the Intercom is automatically closed

after 40 seconds.

Attention: If needed, you can disable the VOX feature simply by pressing

the “Volume -” button for 3 sec. A voice announcement will advise you

when the VOX is disabled. To turn the VOX on again, just press the same

button and a voice announcement will advise you that the VOX is now

active. This setting is remembered also in you turn o the unit.

How to pair the BT City to previous BT line unit

The BTCity is compatible with all the BT line unit from Midland. You

can pair the BTCity to a BT2, BT1, BTX1, BTX2 or BTNext unit and the

max distance of the intercom is dened from the lower possible.

To pair the BTCity to another BT line unit, you must rst enter the

setup mode:

1. Turn o the unit

2. Press and hold down the Middle button about 7 sec., until the Red

light is on permanently.

3. Now press long (3 sec) the “Control” button, the Blue and Red light

will ash.

4. Follow the procedure on the other unit’s instruction manual (nor-

mally you can use the “Volume +” button on all the previous BT

line units like BT1-BT2).

5. When successfully paired, each unit will have the Blue light on

for one second and than go back to the setup mode (Red light

always on).

If you don’t have more devices to pair, you must exit the setup mode

from both units before you can use them: for BTCity double click on

the “Control” button, the Red light will turn o and the Blue light will

start ashing. For the other devices of BT line, please refer to their

own user manual.

Resetting all paired devices

Sometimes you may nd it necessary to delete all the pairing referen-

ces stored in the BTCity unit (reset operation).

› To perform this operation, switch o the BTCity and keep pressed

the “Control”. The red led turns on.

› Simultaneously press and hold down the “Volume +” and “Volume

–“ buttons for 3 seconds. The Blue Light will be lit on for 1 sec.

This procedure deletes all the paired Bluetooth devices stored in the

memory and it is therefore possible to start a new “clean” pairing

session.

Using the wired audio input

Your Midland BTCity is also supplied with a wired audio input (labeled

AUX), that can be used to connect an audio source, like an iPod (or

any other MP3 Player) or a PMR446 transceiver for communications

in group or for a coverage increase.

Priority: the wired audio input has the lowest priority when compared

to the other Bluetooth connections (including the Intercom) and will

therefore always be disabled when another Bluetooth communication

is opened.

Using a i-Pod/MP3 Player

Listening to music

To listen to music from the wired input, connect the audio source

using the cable supplied with the BTCity unit. The volume level is au-

tomatically adjusted by the AGC system, which means that you only

need to adjust the volume of your iPod/ MP3 player to a level that will

allow you to listen to music in normal speed.

GPS Navigator with stereo music player

If the GPS is also a stereo MP3 player and you want to listen to stereo

music, you must pair the GPS to the “Volume +” button. In this con-

guration the GPS street voice announcements will interrupt all other

communication (Intercom, Music).

When the GPS is paired to the “Volume +” button the “Phone” mode

is activated.

Attention: It is possible to listen A2DP Stereo music from the

GPS only in “Phone Mode”.

How to pair the BTCity to a GPS

In general is possible to pair the BTCity to all the GPS for motorbike that

support Bluetooth headset connection.

To pair the BTCity to a GPS, you must rst enter the setup mode:

1. Turn o the unit

2. Press and hold down the “Control” button about 7 sec., until the Red

light is on permanently.

3. Now press rmly (3 sec) the “Volume +” or “Volume -” button, the

Blue and Red light will ash.

4. Enable the Bluetooth device search feature on your GPS

5. After some seconds, “Midland BTCity” will be displayed on your GPS.

6. Follow the pairing procedure of your GPS. If a pin code is requested

you must enter “0000” (four times zero).

7. When successfully paired, the Blue light of the unit will be on for one

second and then the unit will exit the setup mode and switch to the

working mode (the Blue light will start ashing).

You can now use your BTCity and the GPS street voice announcement

are always in background.

If you pair the GPS to the Volume + button (because for example the

“Volume –“ button was already used), you loose the possibility to pair

the phone to the BTCity unit. You can overcome this limit by pairing the

phone directly to the GPS and then the GPS to the BTCity unit. All the

phone features are therefore managed by the GPS itself.

How to use a GPS

When paired using the “Volume -” button the GPS will be automatically

connected and the voice announcement are always in background also

if the intercom is active.

When the GPS is paired to the “Volume +” button, the street voice an-

nouncement will always interrupt the intercom. In addition, remember

to switch to “Phone” mode in order to listen and control the music (play/

pause - backward and forward).

If the phone is connected through the GPS you must use the control

buttons on the GPS screen in order to control the phone functionality.

Using the intercom feature

To use the Intercom feature, be sure both BTCity units are turned on

and previously paired together.

The two units supplied in the Midland BTCity TWIN Pack, are already

paired and ready for use, which means that it is not necessary to per-

form this procedure.

If the devices are not part of the same pack, or one of the BTCity units

has been purchased separately, you need to pair them in order to be

able to use the Intercom function.

Pairing with another BTCity device

1. Turn o the unit. Press and hold down the middle button about 7

sec., until the Red light is on permanently.

2. Press the “Control” button on the rst unit until the RED and BLUE

lights begin to ash rapidly and alternately.

3. Then press the “Control“button on the second unit until the RED

and BLUE lights begin to ash rapidly and alternately.

4. Now both BTCity units are trying to pair to each other.

When successfully paired, the blue led of each device will light for

1 sec and go back to setting mode (red light always on) waiting for

additional pairing or setting procedures.

5. To use the two devices, exit the setting mode: Double click on the

“Control” button. The red light will quit and the blue light will be-

gin to ash. Now you can use your BTCity.

Midland BT City 2013 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midland BT City 2013

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info