Bedienungsanleitung Milwaukee 5262-59 (Seite 10 von 11) (Englisch, Französisch, Spanisch)

641642

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Installing Drill Bits and Chisels

Only use accessories with SDS or SDS Plus shanks.

Be sure that the shank of the bit is clean. Dirt par-

ticles may cause the bit to line up improperly. Do not

use bits larger than the maximum recommended

capacity of the drill because gear damage or mo-

tor overloading may result. For best performance,

be sure that the bit is properly sharpened and the

shank is lightly greased before use.

1. Insert the bit or chisel into the nose of the tool.

2. Rotate bit slowly until it aligns with the locking

mechanism.

3. Push bit into tool until it locks.

4. Check that the bit is locked properly; it should

be possible to pull the bit back and forth slightly

(about 1/4”).

5. To remove bits and chisels,

pull bit holder release collar

toward the rear of tool and

remove bit.

NOTE: Use caution when

handling hot bits and chis-

els.

OPERATION

WARNING To reduce the risk of injury,

keep hands and cord away from the bit

and all moving parts.

WARNING To reduce the risk of injury,

wear safety goggles or glasses with side

shields.

WARNING To reduce the risk of injury,

always unplug tool before attaching

or removing accessories or making adjust-

ments. Use only speciﬁ cally recommended

accessories. Others may be hazardous.

Reverse

Forward

Selecting Action

These MILWAUKEE Rotary Hammers have

three settings: drill only, rotary hammer, and

hammer only. Always allow the motor to

come to a complete stop before changing the

mode selection to avoid damage to the tool.

1. For drilling, press in the

selector release button and

turn the selector lever so the

arrow on the lever points to

the twist drill symbol.

2. For rotary hammering, press

in the selector release but-

ton and turn the selector

lever so the arrow points to the hammer and

twist drill symbol.

3. For hammering only, press in the selector release

button and turn the selector lever so the arrow

points to the hammer symbol.

4. To freely rotate the bit to the desired angle for

hammering only, press in the selector release

button and turn the selector lever to the

symbol. Then, follow step 3.

NOTE: To engage the hammering mechanism,

maintain pressure on the bit. When pressure on

the bit is released, the hammering action will stop.

Using the Control Switch

Always allow the motor to

come to a complete stop be-

fore using the control switch.

For forward (clockwise) rota-

tion, push the control switch

to the left side of the tool.

Check the direction of rotation

before use.

For reverse (counterclock-

wise) rotation, push the con-

trol switch to the right side of

the tool. Check direction of

rotation before use.

Starting, Stopping and Controlling Speed

1. To start the tool, grasp the handle ﬁ rmly and pull

the trigger.

2. To vary the speed, increase or decrease the

pressure on the trigger. The further the trigger

is pulled, the greater the speed.

3. To stop the tool, release the trigger. Make sure

the tool comes to a complete stop before laying

the tool down.

Lock-On

The lock-on button holds the trigger in the ON posi-

tion for continuous full speed use.

1. To lock the trigger, hold in the lock button while

pulling the trigger. Release the trigger.

2. To unlock the trigger, pull the trigger and release.

The lock button will pop out.

Operating

Position the tool, grasp the handles ﬁ rmly and pull

the trigger. Always hold the tool securely using

both handles to maintain control. This tool has

been designed to achieve top performance with

only moderate pressure. Let the tool do the work.

If the speed begins to drop off when drilling large

or deep holes, pull the bit partially out of the hole

while the tool is running to help clear dust. Do not

use water to settle the dust since it will clog the bit

ﬂ utes and tend to make the bit bind in the hole. If

the bit should bind, a built-in, non-adjustable slip

clutch prevents the bit from turning. If this occurs,

stop the tool, free the bit and begin again.

MAINTENANCE

WARNING To reduce the risk of injury,

always unplug your tool before per-

forming any maintenance. Never disas-

semble the tool or try to do any rewiring

on the tool’s electrical system. Contact a

MILWAUKEE service facility for ALL repairs.

Maintaining Tools

Keep your tool in good repair by adopting a regular

maintenance program. Before use, examine the gen-

eral condition of your tool. Inspect guards, switches,

tool cord set and extension cord for damage. Check

for loose screws, misalignment, binding of moving

parts, improper mounting, broken parts and any

other condition that may affect its safe operation. If

abnormal noise or vibration occurs, turn the tool off

immediately and have the problem corrected before

further use. Do not use a damaged tool. Tag damaged

tools “DO NOT USE” until repaired (see “Repairs”).

Under normal conditions, relubrication is not neces-

sary until the motor brushes need to be replaced.

After six months to one year, depending on use,

return your tool to the nearest MILWAUKEE service

facility for the following:

• Lubrication

• Brush inspection and replacement

• Mechanical inspection and cleaning (gears,

spindles, bearings, housing, etc.)

• Electrical inspection (switch, cord, armature, etc.)

• Testing to assure proper mechanical and electri-

cal operation

WARNING To reduce the risk of injury,

electric shock and damage to the tool,

never immerse your tool in liquid or allow a

liquid to ﬂ ow inside the tool.

Cleaning

Clean dust and debris from vents. Keep the tool

handles clean, dry and free of oil or grease. Use

only mild soap and a damp cloth to clean your tool

since certain cleaning agents and solvents are

harmful to plastics and other insulated parts. Some

of these include: gasoline, turpentine, lacquer thin-

ner, paint thinner, chlorinated cleaning solvents,

ammonia and household detergents containing

ammonia. Never use ﬂ ammable or combustible

solvents around tools.

Repairs

If your tool is damaged, return the entire tool to the

nearest service center.

ACCESSORIES

For a complete listing of accessories refer to your

MILWAUKEE Electric Tool catalog or go on-line

to www.milwaukeetool.com. To obtain a catalog,

contact your local distributor or a service center.

WARNING To reduce the risk of injury,

always unplug the tool before attaching

or removing accessories. Use only speciﬁ -

cally recommended accessories. Others may

be hazardous.

Milwaukee 5262-59 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info