Bedienungsanleitung Mitsubishi HD5000 (Seite 20 von 24) (Englisch)

30505

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

• There is no audio and video from the IEEE  device. • The device is not turned on - turn the device power on.

• No media (tape or disc) is inserted into the device.

• The media is blank (has no recording).

• The play command failed - Try pressing play again on the

device’s remote control or front panel.

• The device is already in use (for example the device is currently

recording).

• The source is copy-protected or violates copy-protection.

• The device’s digital video signal is not supported by the TV, such as

DV video common with camcorders. Use analog connections instead,

if available.

• The device is not an audio/video device.

• Too many other devices are already communicating over

IEEE . Remove or stop some devices and try again.

• The IEEE  device cannot be selected. • Both IEEE  devices and Ant-DTV can not be displayed in the

PIP.

• The device may be busy, either recording or a peer-to-peer

connection has been established. Cancel the recording or

peer-to-peer connection.

• The IEEE  Device is not listed in the Device Selection

menu.

• The device is unchecked in the Review screen.

Go to Setup in the Main menu, select Edit NetCommand Setup,

then select Review. Verify the device is checked.

• The IEEE  plug is disconnected or loose.

• The IEEE  Device has not been powered On. Turn on the

device’s power.

• The device has not been discovered.

• The device is not an Audio/Video device.

• Cannot record to or from the IEEE  device, including Dub

recordings

• To initiate a recording to IEEE  device, first select the

source device to record, such as Ant-DTV (NOT the recording

device). Then press the REC key. The Record/Connect menu

displays allowing setup of the recording.

• The source device for the recording is not powered on.

• For a dubbing, the destination device for the recording is not

powered on.

• The wrong media, (analog tape for digital recording, or

digital tape for the analog recording) is in the device.

• Either the program is copy protected, or if there are multiple

subchannels and one of the programs (not necessarily the

program requested) is copy protected.

• The program has already been recorded once and the copy

protection only allows one recording.

• Unapproved source device for copy protected material.

• The recording device can not decode the copyright signal

included in the signal source (try another device if available).

• The playing device (for dubbing) does not support copyrighted

material.

• Source for recording is copyrighted.

• Too many IEEE  devices in network. Insufficient bandwith

available. Disconnect unused devices.

• Source Device has higher speed (S ) than record device. If

possible, reverse devices, play in the slower device and record in

the faster device.

• DEVICE MENU button does not display a menu. • The IEEE  device does not provide a menu.

• Cannot control the IEEE  device from the Transport Menu. • Device may not support the command.

• Selected function is gray (such as Record for a DVD, which does

not support the Record function.

Problem Possible Solution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi HD5000 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info