Bedienungsanleitung Mitsubishi XL6500U (Seite 44 von 48) (Englisch)

493642

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

EN-44

Troubleshooting (continued)

Images are not displayed correctly. (continued)

Problem Solution

Projected images are

obscured.

• Match the output resolution of your computer with the resolution of the projector. For

the method to change the output resolution of the computer, contact the manufacturer

of your computer. (See page 46.)

• Some images and texts appear obscured during the keystone adjustment. In such

cases, use the projector without applying the keystone adjustment. (See page 11.)

Image cannot be

displayed correctly

even when the

computer’s resolution

is set to 1920 x 1080.

• Some computers output signals not supported by this projector even when its resolution

is set to 1920 x 1080. Take the following procedures in order.

1. Connect the computer to the COMPUTER/COMPONENT VIDEO IN 2 terminal and

reboot the computer.

• DDC conﬁ gures the computer so that it will output proper signals. (See page 14.)

2. Set the refresh rate of the computer to 60 Hz and make adjustment according to

“How to adjust the computer image” on page 30.

• When an unsupported signal is input, it may be displayed consisting of every

other pixel. In this case, decrease the resolution of the computer.

Noise appears around

the image.

• In some images such as DVD, noise may appear around the recorded image. In this

case, decrease the setting value of OVER SCAN of the SIGNAL menu. (See page 26.)

Others

Problem Solution

The exhaust vents

emit warm air.

• This air comes out after cooling the inside of the projector. You may feel hot, but this

is not a malfunction.

No audio is output. • Check that the volume isn’t set to low.

The menu can’t be

used.

• The microcomputers inside the projector may be wrongly operating because of noise.

Turn off the main power, wait about 10 minutes, and turn on the main power again.

“TEMPERATURE!!” is

displayed.

• This indication appears when the ambient temperature rises high. When the ambient

temperature stays high, the lamp goes out.

Eliminate any causes of the rise in the ambient temperature.

• This indication appears when the air inlet or outlet grille is blocked. When they are

kept blocked, the lamp goes out.

Remove the objects blocking the air inlet or outlet grille.

The

mark appears. • This mark appears when ineffective operation is carried out. This isn’t a product

malfunction.

The remote control

doesn’t function easily or

at all.

• Check that the batteries are loaded in the remote control or the batteries are not weak.

(See page 6.)

• Check that the remote control sensor isn’t exposed to direct sunlight or ﬂ uorescent

light. (See page 9.)

• Use the remote control within its operation range. (See page 9.)

• Use the remote control at least 10 cm away from the projector.

The buttons on the

control panel (except

for the POWER button)

don’t function.

• PASSWORD FUNCTION in the FEATURE menu has been set to MENU ACCESS to

enable the password lock.

Cancel the password lock or contact the person in charge of management of the

projector. (See page 33.)

Alarm sounds. • To temporarily halt the anti-theft alarm device, insert the safety pin. (See page 38.)

If the following problem occurs after the lamp is replaced, check the following ﬁ rst.

Problem Solution

The projector does not

turn on.

• Fit the lamp cover securely. (See pages 39 and 40.)

• Reset the lamp operating time. (See page 40.)

The STATUS indicator

blinks.

• Reset the lamp operating time. (See page 40.)

Kensington Lock

This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System.

Refer to the information that came with the Kensington System for instructions on how to use it to secure the

projector. Please contact Kensington Technology Group below.

Kensington Technology Group

2855 Campus Drive

San Mateo, CA 94403, U.S.A.

Phone: +1- (650)572-2700 Fax: +1- (650)572-9675

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi XL6500U Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info