646346
5
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
Selecting the required power
Turn the power selector (1) to obtain the desired power.
MAX position indicates 100% power.
MIN position indicates 50% power.
Selecting the hot water temperature
Turn the water temperature dial (2) to obtain the desired
temperature.
MAX position indicates the maximum temperature (minimum flow).
MIN position indicates the minimum temperature (maximum flow).
IMPORTANT: This heater is not thermostatic.
Note: It is advisable to adjust both the power and the water temperature to the
minimum value necessary to cover your requirements. This will save energy and
prolong the life of the appliance, reducing scale deposits on the heat exchanger.
Switching off the water heater
When the hot water tap is turned off, the heater will stop automatically.
To switch off the heater completely, press the ON-OFF button (3).
IMPORTANT: When the heater is switched on for the first time, or if it has
not been used for a certain time, or when a new gas bottle is installed, the
appliance may fail to ignite due to the presence of air in the gas pipes. If
this happens, the heater will ‘LOCK OUT’ and the red LED (4) will be
displayed.
Occasionally, the heater may fail to ignite due to excessively windy
conditions or other adverse atmospheric conditions, causing ‘LOCKOUT’.
Insufficient gas pressure (faulty regulator) or fluctuations in voltage may
also cause ‘LOCKOUT’.
To RESET the heater press the ON-OFF button to switch off then depress the
ON-OFF button to restart. The red LED should now be off and the heater
should ignite when the hot tap is opened.
If the heater locks out persistently, call your installer or MORCO on 01482
325456 for details of your nearest service agent.
Combustion product removal control device (Air pressure switch)
IMPORTANT: The user must not interfere in any way with this device. Under no cir-
cumstances may it be disconnected, modified or replaced by a different part.
If the flue becomes blocked for any reason, or it is contaminated the heater
will ‘LOCKOUT’. It will be impossible to re-start the heater without fixing the
problem. You should call your installer or phone MORCO on 01482 325456.
5
USER
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Morco F-11E wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Morco F-11E

Morco F-11E Zusatzinformation - Englisch - 1 seiten

Morco F-11E Bedienungsanleitung - Holländisch - 18 seiten

Morco F-11E Bedienungsanleitung - Französisch - 18 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info