Bedienungsanleitung Morso 3100 series (Seite 16 von 19) (Englisch, Dänisch)

744324

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

DK ENG

3.0 Routine stove maintenance

3.1 External maintenance

The surface of the stove is painted with heat-resistant Senotherm paint. If the stove is used

too vigorously, the painted surface may take-on a greyish tinge. It is easily maintained by sim-

ply vacuuming the surface with a soft brush attachment and applying two light layers of paint.

Morsø stoves are painted using a Morsø Original Black (previously called Morsø dark grey)

or Morsø grey. The paint can be bought in a spray or a can.

3.2 Internal maintenance

Ceramic glass

If the stove is used and installed onto a ue with the correct draft, very little or no deposits

should appear on the ceramic glass. It is usual for soot deposits to appear during long slum-

bering res however, once the re has been re-established to a burn brightly, these deposits

should burn o.

If the glass window becomes thoroughly covered in soot due to faulty operation or poor

draft, the soot can be easily removed using, e.g. Morsø Glass Cleaner, but please ensure that

the glass is cold before cleaning. Avoid fuelling the stove with wood that is so long that it

presses against the glass when the door is closed.

Ceramic glass replacement

Ceramic glass cannot be recycled because it has a higher melting point that ordinary glass.

If ceramic glass is mixed with ordinary glass, the raw material is spoiled, and the reclaiming

process may be halted. Take care that the ovenproof glass does not end up among ordinary

recycled waste. That will be a great benet to the environment.

Note: Should be handed in to a recycling station as ceramic glass.

Internal cast-iron parts and/or wear components

The shaking grate, bae plate and other internal components that are in direct contact with

the re are all constituted as ‘wear’ components or consumables, as, they are exposed to

the most wear. When used properly, these parts will last for many years, but overly vigorous

use will naturally shorten the lifespan. The aforementioned parts are all easily replaceable.

If the bae plate is damaged or warped and is not replaced in time, the top plate could be-

come subject to excessively high temperatures, which may lead to damage here also.

Note: that no unauthorised alterations to the stove design should be undertaken, and

always ensure that any replacement parts purchased are Morsø original parts.

Reasons for sooty glass window:

- The fuel is too wet.

- The pieces of fuel are to big/uncut wood.

- The combustion temperature is too low.

- Too much air coming through the bottom grate.

- Poor chimney draft.

Reasons for overly rapid wear of internal parts

- Stove red too vigorously.

- Too much air coming through the bottom grate.

- Use of very dry wood (wood from old furniture).

- Too much soot on top of the baes (please see the section on Cleaning).

- Too much ash in the ash pan (please see the section on Ash).

Gaskets

The rope gaskets in the door will need regular inspection in order to ensure and maintain

full control of your stove’s burning rate; over time the rope gaskets will harden and will be-

come less airtight; at this point you will need to remove and replace with new. Use only the

genuine Morsø gasket kit, which comes with detailed replacement instructions.

NOTE: Normal wear components (inner parts) are not covered by Morsø’s 10-year

guarantee.

Maintenance products (Spare Parts, Glass Cleaner, Paint, Gasket Kit, etc) are all available from

your authorised Morsø dealer.

3.3 Cleaning the stove

During normal use and sweeping of your stove and chimney, a layer of ash, soot or debris

can form, particularly on the top of the bae plate or inner reback. Any deposits allowed

to build-up over time will have an insulating eect on these parts, thus restricting expan-

sion; this will ultimately result in a shorter lifespan. The chrome-iron bae plate and inner

reback/bricks can easily be removed from the stove and should be regularly checked for

debris and cleaned. You must ensure that your chimney sweep removes all soot and debris

from the stove after the sweeping process.

Your chimney should be swept at least once a year; however a regular inspection of your stove-

pipe and chimney will determine whether a more frequent approach should be adopted.

Ash

In order to achieve the highest combustion temperature possible when burning solely wood,

it is important that a 1cm deep bed of ash is established on top of the grate area. Excess ash

should be removed by simply agitating the grate by moving the riddling rod on the outside

of the stove; surplus ash will fall into the ash pan below the grate where it can be easily and

safely removed.

Be sure to empty the ash pan before it gets completely full; if the ash level reaches the under-

side of the grate, air ow through the grate will be restricted and will lead to over-heating and

premature wear of the grate parts.

When emptying the ash pan always dump the waste ash into a metal container (dustbin)

where it can fully cool before being taken away by your refuse collector. Ash from a wood-

burning stove does not benet your garden as fertiliser.

Morso 3100 series Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Morso 3100 series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info