Bedienungsanleitung Morso 6141 (Seite 19 von 21) (Englisch, Dänisch)

744335

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

DK ENG

4.0 HETAS amendments

Health and safety precautions

Special care must be taken when installing the stove such that the requirements of the Health

and Safety at Work Act are met.

Handling

Adequate facilities must be available for loading, unloading and site handling.

Fire Cement

Some types of re cement are caustic and should not be allowed to come into contact with

the skin. In case of contact wash immediately with plenty of water.

Asbestos

This stove contains no asbestos. If there is a possibility of disturbing any asbestos in the course

of installation then please seek specialist guidance and use appropriate protective equipment.

Metal Parts

When installing or servicing this stove care should be taken to avoid the possibility of per-

sonal injury.

Note of references to the current UK regulations

In all cases the installation must comply with current Building Regulations, Local Authority

Byelaws and other specications or regulations as they aect the installation of the stove.

It should be noted that the Building Regulations requirements may be met by adopting the

relevant recommendations given in British Standards BS 8303, BS EN 15287-1:2007 as an

alternative means to achieve an equivalent level of performance to that obtained following

the guidance given in Approved Document J.

Please note that it is a legal requirement under England and Wales Building Regulations that

the installation of the stove is either carried out under Local Authority Building Control ap-

proval or is installed by a Competent Person registered with a Government approved Com-

petent Persons Scheme. HETAS Ltd operate such a Scheme and a listing of their Registered

Competent Persons can be found on their website at www.hetas.co.uk.

This stove must not be installed into a chimney that serves any other heating appliance.

More detailed advice about existing chimney usage

NOTE: A chimney height of not less than 4.5 metres measured vertically from the outlet of

the stove to the top of the chimney should be satisfactory. Alternatively the calculation proce-

dure given in EN 13384-1 may be used as the basis for deciding whether a particular chimney

design will provide sucient draught.

The outlet from the chimney should be above the roof of the building in accordance with

the provisions of Building Regulations Approved Document J.

If installation is into an existing chimney then it must be sound and have no cracks or other

faults which might allow fumes into the house. Older properties, especially, may have chim-

ney faults or the cross section may be too large i.e. more than 230 mm x 230 mm. Remedial

action should be taken, if required, seeking expert advice, if necessary. If it is found neces-

sary to line the chimney then a ue liner suitable for solid fuel must be used in accordance

with Building Regulations Approved Document J.

Any existing chimney must be clear of obstruction and have been swept clean immediately

before installation of the stove. If the stove is tted in place of an open re then the chimney

should be swept one month after installation to clear any soot falls which may have occurred

due to the dierence in combustion between the stove and the open re.

If there is no existing chimney then any new system must be to the designation described

above and in accordance with Building Regulations Approved Document J.

A single wall metal uepipe is suitable for connecting the stove to the chimney but is not

suitable for use as the complete chimney. The chimney and connecting uepipe must have

a minimum diameter of 150 mm and its dimension should be not less than the size of the

outlet socket of the stove.

Any bend in the chimney or connecting uepipe should not exceed 45°. 90° bends should

not be used.

Combustible material should not be located where the heat dissipating through the walls of re-

places or ues could ignite it. Therefore when installing the stove in the presence of combustible

materials due account must be taken of the guidance on the separation of combustible material

given in Building Regulations Approved Document J and also in these stove instructions.

If it is found that there is excessive draught in the chimney then a draught stabiliser should be

tted. Fitting of a draught stabiliser will aect the requirement for the permanent air supply

into the room in which the stove is tted in accordance with Approved Document J (see also

combustion air supply).

Commissioning and handover

Ensure all parts are tted in accordance with the instructions.

On completion of the installation allow a suitable period of time for any re cement and mor-

tar to dry out, before lighting the stove. Once the stove is under re check all seals for sound-

ness and check that the ue is functioning correctly and that all products of combustion are

vented safely to atmosphere via the chimney terminal.

On completion of the installation and commissioning ensure that the operating instructions

for the stove are left with the customer. Ensure to advise the customer on the correct use

of the appliance and warn them to use only the recommended fuel for the stove.

Advise the user what to do should smoke or fumes be emitted from the stove. The customer

should be warned to use a reguard to BS 8423:2002 (Replaces BS 6539) in the presence of

children, aged and/or inrm persons.

Warning note on fume emission

Properly installed, operated and maintained this appliance will not emit fumes into the dwelling.

Occasional fumes from de-ashing and re-fuelling may occur. However, persistent fume emis-

sion is potentially dangerous and must not be tolerated. If fume emission does persist, the fol-

lowing immediate actions should be taken:

A. Open doors and windows to ventilate room.

B. Let the re out or eject and safely dispose of fuel from the appliance.

C. Check for ue or chimney blockage, and clean if required.

Do not attempt to relight the re until the cause of the fume emission has been identied

and corrected. If necessary seek expert advice.

Morso 6141 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Morso 6141

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info