Bedienungsanleitung Morso 7843 (Seite 35 von 40) (Englisch, Dänisch)

744306

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

NO SV

Internal cast-iron parts and/or wearing parts

The baes and other components that come in direct contact with the re and glowing

fuel are all wearing parts. As a result, they will be particularly susceptible to burn-through.

When used correctly, these parts will last for many years, but overly vigorous use will natu-

rally accelerate the burn-through. Such parts are all easily replaced.

If the baes are damaged and are not replaced in time, the top plate will be exposed to

such high temperatures that it may be damaged as well.

Please note that no unauthorised alterations of the design may be undertaken, and

that any parts that are replaced must be replaced with original Morsø parts.

Gaskets

The gaskets in the door will wear out over time, and should be replaced as required in or-

der to prevent runaway combustion. Use the original Morsø gasket kit.

NOTE: Normal wearing parts are not covered by Morsø’s extended warranty.

A selection of maintenance products (spare parts, glass cleaner, paint, gasket kit, etc.)

is available from your Morsø dealer.

3.3 Cleaning the stove

A layer of ash and soot will form as a result of the draught in the chimney and after sweep-

ing, particularly on the top of the casted smoke hood. This ash will have an insulating ef-

fect, which may speed up the burn-through of the bae.

During normal cleaning, the bae and the smoke hood can be removed from the stove.

Once these parts have been taken out, you can access the ue chamber above the bae

and clean it.

Clean the bae and smoke hood before reassembling them, and make sure that they are

correctly assembled. Nowadays the chimney sweep must remove the soot in the stove, in ad-

dition to sweeping the chimney and cleaning the ue pipe. The number of annual sweepings/

cleanings of the stove should be determined in consultation with your chimney sweep.

Ash

As noted above, there should be a couple of centimetres of linsulating ash in the bottom of the

combustion chamber in order to achieve a high combustion temperature. If the layer of ash is

too thick, it can be brushed down into the ash pan. Empty the ash pan before it gets comple-

tely full, so that the ash does not insulate around the grate, and thereby speed up the burn-

through. In most cases, the ash will need to be taken away by the waste disposal company. Be-

cause embers may be concealed in the ash pan for several days, it may be necessary to store

the ash in a container made of non-ammable material before pouring it into a rubbish bag.

Reasons for overly rapid wear of internal parts

- Stove red too vigorously

Use of very dry wood (wood from old furniture)

- Too much soot on top of the baes (please see the section on Cleaning)

- Too much ash in the ash pan (please see the section on Ash)

Note: Should be handed in to a recycling station as ceramic glass.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Morso 7843 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Morso 7843

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info