Bedienungsanleitung MTD 1043 (Seite 10 von 15) (Englisch)

672424

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Operating manual English

Operating and display

elements

`~ìíáçåK=

a~ã~ÖÉ=íç=íÜÉ=~ééäá~åÅÉ

qÜáë=Ñáêëí=ÇÉëÅêáÄÉë=íÜÉ=Åçåíêçä=~åÇ=

Çáëéä~ó=ÑìåÅíáçåëK=aç=åçí=ÉñÉÅìíÉ=

~åó=çÑ=íÜÉëÉ=ÑìåÅíáçåë=óÉí>

Fig. 1

1 Exhaust cover

2 Spark plug

3Starter handle

4 Tank cap

5 Intake pump/primer

6Choke lever

7 Air filter cover

8 Handle bar

9 Shaft

10 Cutting attachment cover

11 Line cutting blade

12 Line coil

13 Gearbox

14 Holder for cutting

attachment cover

15 Holder for cable harness

16 Throttle

17 Ignition switch

18 Throttle lock

19 Shoulder belt holder

20 Cutting blade with cutting

attachment cover *

21 Retaining bar *

22 Socket wrench *

* depending on model

Installation manual

a~åÖÉê

oáëâ=çÑ=áåàìêó=Ñêçã=ÉåÖáåÉ=ÄÉáåÖ=

ëí~êíÉÇ=ìåáåíÉåíáçå~ääóK

mêçíÉÅí=óçìêëÉäÑ=Ñêçã=áåàìêóK=

_ÉÑçêÉ ïçêâáåÖ=çå=íÜÉ=ÉåÖáåÉW

Ó pïáíÅÜ=çÑÑ=íÜÉ=ÉåÖáåÉI

Ó t~áí=ìåíáä=~ää=ãçîáåÖ=é~êíë=Ü~îÉ=

ÅçãÉ=íç=ëí~åÇëíáääX=íÜÉ=ÉåÖáåÉ=

ãìëí=Ü~îÉ=ÅççäÉÇ=ÇçïåK

Ó oÉãçîÉ=ëé~êâJéäìÖ=íÉêãáå~äK

Disposal instructions

Dispose of packaging remnants,

old units, etc., in accordance with

local regulations.

Installing and setting the

handle bar

Fig. 2

 Insert the handle bar (1) into the

lower holder (2).

 Hook the upper retaining plate (3)

into the openings (4) of the lower

holder and secure with the toggle

screw (5).

 Hold the unit in the operating

position (Fig. 13) and position the

handle bar until you have a secure

footing.

 Tighten the toggle screw (5) firmly

until the handle bar (1) is secure.

 Press the cable harness (6) into

the holder (7).

Adjusting the carrying

system (shoulder strap)

Fig. 3

1. Place harness over your

shoulders.

Close the catch on the chest belt.

If required, readjust.

Close the catch on the abdominal

belt. If required, readjust.

4. Adjust the shoulder, abdominal

and chest belts to the correct

length/width.

5. Latch the hook of the carrying

system into the holder on the unit

and adjust the attachment pad to

a comfortable length.

Attaching the cutting

attachment cover

Fig. 4



Attach cutting attachment cover (1)

to the holder (2) using the two

screws (3).

 Tighten screws firmly.

Attaching/removing

the line head

Attaching the line head

Fig. 5

 If attached, remove cutters and

blade attachment parts before-

hand. See “Removing the cutting

blade”.

 Push spacer (1) onto the

drive shaft (2).

Align the 3 openings in the

spacer (3), the gearbox (4) and

the gear cover (5).

Note

If alignment is not correct, the line

head cannot be attached/removed!

 Insert retaining bar (6) through the

openings (3, 4, 5) in order to secure

the gearbox.

 While holding the retaining bar (6),

turn the line head (7) anti-clockwise

(to the left) onto the drive shaft.

Tighten line head firmly!

Note

Ensure that the line head (7) is

seated correctly on the spacer (1),

i.e. centred and resting flat!

 Remove retaining bar from the

gear head.

Remove the line head

Fig. 6

 Align the openings (3, 4, 5). Insert

retaining bar (6) through the

openings and hold in position.

 Unscrew line head (7) clockwise

(to the right) off the drive shaft.

Attaching/removing the

cutting blade (depending

on model)

Attaching the cutting blade

Fig. 7

 If attached, remove the line head

beforehand. See “Attaching/

removing the line head”.

Note

When attaching the cutting blade

for the first time, remove the blade

attachment parts (blade holder (8),

retaining bell (9), nut (10)) if attached.

See “Removing the cutting blade”.

 Push spacer (1) onto the

drive shaft (2).

Align the 3 openings in the spacer

(3), the gearbox (4) and the gear

cover (5) (Fig. 5).

Note

If alignment is not correct, the cutting

blade cannot be attached/removed!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD 1043 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD 1043

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info