Bedienungsanleitung Mtx audio th904 (Seite 4 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

168698

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

www.mtx.com - www.mtx.eu.com

Owner’s Manual - TH904

Connectors panel :

RCA Inputs - These RCA inputs are used with source units that have RCA or

Line level outputs. (Source units need a minimum level of 100mV output for

proper operation of the amplier).

MTX recommends only high quality twisted pair cables (such as StreetWires)

to decrease the possibility of radiated noise entering the system.

High Level Inputs :

MTX ampliers allow high level inputs through RCA type input connections.

Simply connect the head unit speaker leads to the provided adapters.

Speaker Terminals - Connect speakers to these terminals. Observe speaker

polarity throughout the system. Improper phase can result in loss of bass re-

sponse and/or poor overall sound quality.

Bridge Mode:

When bridging the amplier, use the left positive terminal and the right negative terminal only.

Warning : do not bridge the amplier with an impedance lower than 4 ohm.

Thermal Protection - This LED illuminates red when the amp reaches 100°C. The LED also turns red when the

power supply goes below 9V or over 16.2V.

Short Circuit Protection - This LED will ash yellow when the speaker outputs will short circuit. Without signal,

this LED can remain yellow when the speaker outputs are short circuited.

Fuses - When fuses blow, replace them with the same value. Never use a higher rated fuse !

(+12) Power Terminal - This is the main power input for the amplier and must be connected directly to the posi-

tive terminal of the vehicles battery for proper operation. Use caution when installing (+12) power cable in the

vehicle. Avoid running this cable parallel with RCA cables, antennas, or other sensitive equipment due to massive

currents that can induce noise into the audio system. It is also very important to have a tight, secure connection

for maximum performance. MTX recommends using 21mm

power wire with the MTX TH904 amplier.

Remote Terminal – The amplier can be turned on by applying 12 volts to this terminal. Typically this voltage is

supplied by a wire from the source unit marked "remote" or "power antenna".

Ground Terminal – A proper ground is required for your amplier to operate at peak performance. A short ground

cable the same diameter as the power cable should be used to attach the ground terminal directly to the chassis

of the vehicle. Always remove paint, dirt or debris to expose bare metal where the ground will be attached.

Input Switch : If the head unit is equipped with 4 RCA outputs (2 front and 2 rear), use the 4ch mode and connect

the 4 RCA outputs to the 4 RCA inputs on the amp. If only 2 RCA outputs are available from the head unit, use the

2ch mode to feed the entire amp.

High level inputs

through RCA

Adaptors

included

To Head

Unit

Speakers

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mtx audio th904 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info