Bedienungsanleitung MTXaudio RT1000-1D (Seite 3 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

490358

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Control Panel

Gain Control (GAIN) - The gain control matches the input sensitivity of the amplier to the source unit being

used. The operating range varies from 100mv to 6V.

Adjusting the gain

1. Turn the gain control on the amplier all the way down (counter clockwise).

2. Turn up the volume control on the source unit to approximately 3⁄4 of maximum.

3. Adjust the gain control on the amplier until audible distortion occurs.

4. Adjust the gain control down until audible distortion disappears.

5. The amplier is now calibrated to the output of the source unit.

Low Pass X-Over Frequency Control (LP X-OVER)

Used to select the desired low-pass (LP) x-over frequency. The frequency is adjustable from 40Hz to 180Hz.

Subsonic lter Control (SUBSONIC)

Used to select the desired subsonic x-over frequency. The frequency is adjustable from 0 to 50Hz.

A subsonic lter is a high-pass high-slope x-over designed to cut the low frequencies that are not able to be

reproduced by a subwoofer system or not part of the audio sprectrum. It also protects your subwoofer(s)...

Adjusting the Subsonic ﬁlter :

1. Turn the subsonic control all the way down to 0 (counter clockwise).

2. Turn up the volume control on the source unit to approximately half power.

Use an extreme bass track. It must go deep and be very loud in bass.

3. Turn the subsonic control clockwise until you can hear the bass level decreasing.

4. Go back (counter clockwise) 2 hours. An average setting is around 25Hz (Control position : 12 o’clock)

5. The subsonic ltre is now calibrated.

RCA Inputs (INPUT) - These RCA inputs are used with source units that have RCA or Line level outputs. (Source

units need a minimum level of 100mV output for proper operation of the amplier).

MTX recommends only high quality twisted pair cables (such as StreetWires) to decrease the possibility of radi-

ated noise entering the system.

RCA outputs (OUTPUT) - These RCA output jacks are for connecting multiple ampliers to 1 stereo RCA lead com-

ing from the source unit (daisy chaining).

External Bass Control (EBC Port) - The Remote Subwoofer Level Control (EBC) plugs directly into this port, while

the EBC itself can be placed anywhere in the vehicle for on demand bass adjustments. EBC is included.

PowerOn/Protection LED - The LED illuminates red when the amp is switched on. When the amps is in shortcir-

cuit or thermal protection, the LED is blinking. You need to switch o and on the amp to restart.

(+12V) Power Terminal - This is the main power input for the amplier and must be connected directly to the pos-

itive terminal of the vehicles battery for proper operation. Use caution when installing (+12) power cable in the

vehicle. Avoid running this cable parallel with RCA cables, antennas, or other sensitive equipment due to massive

currents that can induce noise into the audio system. It is also very important to have a tight, secure connec-

tion for maximum performance. MTX recommends using 50mm

power wire with the MTX RT1000.1D amplier.

Remote Terminal (REM) - The amplier can be turned on by applying 12 volts to this terminal. Typically this volt-

age is supplied by a wire from the source unit marked “remote” or “power antenna”.

Ground Terminal (GND) - A proper ground is required for your amplier to operate at peak performance. A short

ground cable the same diameter as the power cable should be used to attach the ground terminal directly to

the chassis of the vehicle. Always remove paint, dirt or debris to expose bare metal where the ground will be

attached.

Speaker Terminal (SPEAKER) - Connect subwoofer(s) to these terminals. Observe speaker polarity throughout the

system. Improper phase can result in loss of bass response. This is a mono bloc amp with only one channel. The

two (+) are wired in parallel in the amp, and the two (-) are wired in parallel in the amp.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTXaudio RT1000-1D Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info