Bedienungsanleitung Muller FU 35.00 pro (Seite 2 von 2) (Deutsch, Englisch)

683985

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

BA FU30pro HM; DE,GB - 22895 - EIGENDRUCK - V05

Radio receiver GPS-time FU 30 pro

Safety issues Technical

data

!!!ATTENTION!!! Risk of fire and electric shock! Installation and

assembly of electrical equipment must be carried out by skilled

person!!!

Connect the supply voltage/frequency as stated on the product

label!

Warranty void if housing opened by unauthorised person!

The electronic circuit is protected against a wide range of external

influences. Incorrect operation may occur if external influences

exceed certain limits!

Supply voltage

12 -

30VDC SELV (max. 10,8 - 32VDC)

/ supply

= extern

Power consumption

Ø 30mA at 12V / 15 mA at 30V

Output signal

DCF time telegram (no weather data)

Polarity output signal LOW activ

Output type Open Collector wiring:

Umax. 50 VDC

Imax. 80 mA

Max. output power 200 mW

Output voltage LOW 2,5 VDC

Protection type

IP 54

to DIN EN 60529

mbient temperature

-30°C … 55°C

Specifications // Compliance

EN 60730 // CE

Housing

self-extinguishing thermoplast

ssembly

wall mounting with mounting bracket

Recommend wire

shielded

cross-section 0,33 to 2,5 mm2

Subject to technical changes

Connection diagram Installation instruction



Make sure that the GPS time receiver

(top of the device) has free view to sky. Trees, walls, and so on, can

severely degrade the satellite reception capability of the receiver.



Make sure that there are no transformers, relays, switches, or similar devices within a radius of one meter

around the GPS time receiver.



If mounted on wall, avoid electric cables and other disturbing metal in the wall.



If the LED on the bottom side of the device is NOT flashing:

Check proper connection



The LED on the bottom side of the device is flashing fast (5 Hz):

Connection OK / device is waiting for GPS signal (can take up to 15 minutes)



The LED on the bottom side of the device is flashing slow (1 Hz):

Connection OK / GPS signal OK



If the LED on the bottom side of the device is flashing fast longer than 15 minutes (5 Hz):

Possibly no GPS signal. Try to use an alternative position.



It will take several minutes until the time switch is synchronized and the FU/GPS-symbol is displayed

permanently in the time switch.

Installation and connection of the device

Connection / wall mounting



Remove both screws on the bottom side and remove the bottom cover.



Guide wire through the cable sleeve and the hole of the bottom cover.



Connect wire with terminal block according to the above connection diagram.



Assemble cable sleeve on the bottom cover.



Screw the bottom cover.



Install wall mounting bracket and attach GPS time receiver (see drilling plan).

Wiring



Connect GPS time receiver and time switch such that the wiring is not between the mounting wall and the

GPS time receiver.



Max. wire length: 200m



Wire cross-section : 0,33 to 2,5 mm



Avoid parallel placement with other cables,e.g., electric cables, telephone wires, and so on.



RECOMMENDATION: We recommend shielded wires

Display of the time switch Description LED GPS time receiver // FU/GPS-symbol of the time switch



Flashing of the FU/GPS-symbol in the display of the time switch indicates proper connection between time

switch and GPS time receiver after installation.



PLEASE OBSERVE: It can take up to 15 minutes until the FU/GPS-symbol appears/flashes after connecting

the GPS time receiver to the time switch.



The FU/GPS-symbol may flash up to 5 minutes while the time switch is being synchronised. Eventually, after

synchronisation of the time switch, the FU/GPS-symbol

is displayed permanently.



The FU/GPS-symbol is not shown, if the GPS time receiver cannot receive a (valid) GPS signal. Time

accuracy of the time switch is based on its internal quartz.

!!PERMANENT DISPLAY OF THE FU/GPS-symbol

= TIME SWITCH IS SYNCHRONISED!!

LED on the bottom side of the

GPS time receiver

FU/GPS-symbol of the time

switch

STATUS

LED off

The FU/GPS-symbol

is not

visible in the display

=> No supply voltage

=> Wrong connection

LED flashes fast (5 Hz)

The FU/GPS-symbol

flahing in the display

=> Waiting for GPS signal

=> Synchronisation of time switch

LED flashes slow (1 Hz)

The FU/GPS-symbol

permanently visible

=> Valid

GPS

signal

=> Time switch is synchronised

Description DIP switches // Switch positions Drilling plan for wall mounting bracket

!!!NOT TRUE TO SCALE!!!

Switch A Switch B Switch C Switch

Switch

Daylight saving time

ON*

GMT-offset [+]

GMT offset

1 hour

GMT

offset

2 hour

GMT

offset

4 hour

GMT

offset

8 hour

OFF

Daylight saving time

OFF*

GMT- offset [-]

offset

*European daylight saving time rules

Switch position for DCF output signal [default]

[Please note that the DCF signal is without weather broadcast!s]

Switch position for UTC output signal [GMT]

Take care of the environment!

Recycle properly!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Muller FU 35.00 pro Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Muller FU 35.00 pro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info