683912

Muller RC 18.14 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
BA RC1814 N;DE,GB -23609- 2016.03V01 ED Page 2
GB
Instruction manual digital shutter control RC 18.14
Wiring diagram
SAFETY GUIDELINES
Further important indications for using / Intended use
!!WARNING!! ELECTRIC SHOCK CUOLD BE LIVE-DANGEROUS AND FIRE HAZARD!!
=> Installation, connection and installation must be done only by a qualified electrician!
=> Disconnect device from power supply for wiring and installation purposes! Check power supply is disconnected!
When changing the battery, the device must also be disonnected from power supply! Check power supply is disconnected!
=> Damaged devices should not be put into operation and must be immediately removed from service!
To connect only at indicated Power supply and frequency!
No Warranty in case of modification or encroachment!
To install in way that exceptional radiation will not disturb the function of the timer!
Installation and wiring must be done as prescribed by law from local Building and electrical codes!
This Timer is not a toy. Keep away children’s from this Timer!
Persons and object must be kept away from driving range of roller shutters!!
This device serves for the manual and time controlled
switching of roller shutters and.
Read and follow also the installing instruction of the
tubular motor regarding the limit switch setting!
If the device is broken, please take care of
environmentally compatible disposal!
Please keep this instruction manual!
Factory defaults
Switching program: UP 07:00 o’clock ;
DOWN 21:00 o’clock
Time: Preset with 12:00 o’clock
Technical data: Deselect the UP or DOWN drive-times
Power supply:: 230 V/50 Hz ± 10%
Power reserve:
ca. 10 years
Would you like to DESELECT a (particular) UP or DOWN
drive-time, you can set it during the programming (see
programming) on the detail adjustments of the UP and
DOWN drive-times. Adjust this time to the desired UP or
DOWN drive-times as long and until you see the
following display values --:--. The corresponding UP or
DOWN drive-time will NOT be executed.
Power consumption : 0,2
–
0,6W (depending on switching status)
Battery:
Exchangeable / CR 2032
Outputs: 2 NO relays (NOT potential-free)
Type of protection:
IP 20
Switching capacity : 230V / 5A bei cos φ = 1
Class of protection:
II when installed according to regulations
A
mbient temperature : -30°… +50°C
Switching delay:
min. 0,5 Sek.
Mounting: 35 mm DIN-rail
Running time:
2,5 Min.
Housing: Flush-mounted fitting
Program:
A
stro-
und Week-Timer
Accuracy: +/- 1,5 Sec./day (at 20°C) Memory places : 7x UP / 7x DOWN
Buttons / Button-function
Operating modes / Display symbol explanation
Pressing button „UP / Plus“:
UP – command 2,5 Min. or STOP by moving motor
Operating modes
By pressing the Button the mode-functions will be successively activated.
You may choose from three different modes:
Pressing the “Menu Button”:
The “Setting mode” will be activated and a moving motor will be
stopped immediately
Pressing the “Menu Button:
The “Setting mode” will be left and a moving motor will be stopped
immediately
Automatic – Mode (Programmed shifting times are activated )
Manual – Mode (Manual operating)
Random – Mode (Programmed shifting times shifts casually from 01…31
Min. on back)
Displays during operation / Operating mode
Pressing the “OK Button” during Operating mode:
Changing “operation-mode“ or STOP by moving motor
Pressing the “OK Button” during Setting mode:
To confirm the selection or the entered data
Time display
Display of the current day
Displays during setting / Setting mode
Time setting
Pressing button „DOWN / Minus“:
DOWN – command 2,5 Min. or STOP by moving motor
Switching time input according daytime
Switching time input according to sunrise / sunset (ASTRO)
Drive direction (UP/DOWN) of the switching time settings
Selection and setting days / Blocks
SERVICE
Hugo Müller GmbH & Co KG
Sturmbühlstraße 145-149
D-78054 VS-Schwenningen
Tel.: +49 (0) 7720 80 836
E-Mail: info@ hugo-mueller.de
Internet: www.hugo-mueller.de
Programming / Settings instellungen / Programmierung
FURTHER STEPS TO SET TIME AND DAY:
Adjust and select with the PLUS / MINUS buttons the year „ “.
Confirm the setting with the button .
Adjust and select with the PLUS / MINUS buttons the month „ “.
Confirm the setting with the button .
Adjust and select with the PLUS / MINUS uttons the day „ “.
Confirm the setting with the button .
Adjust with the PLUS / MINUS buttons the day-time „ “.
Confirm the setting with the button .
FURTHER STEPS TO TIMER SETTING:
Select with the PLUS / MINUS buttons the way you want to set the program:
=> and Each day singularly
=> and Block wise (Mo-Fr und Sa-Su)
=> Complete week
Confirm your selection with the button
Choose with the PLUS / MINUS buttons between:
=> UP-start time, following the day time
=> UP-start time, according to sunrise (Astro)
Confirm your selection with the button
Set with the PLUS / MINUS buttons the “UP-start“ time(s)
Confirm your selection with the button
Choose with the PLUS / MINUS buttons between:
=> DOWN-start time, following the day time
=> DOWN-start time, according to sunset (Astro)
Confirm your selection with the button
Set with the PLUS / MINUS buttons the “DOWN-start“ time(s)
Confirm your selection with the button
NOTE TO ASTRO SWITCHING-TIMES
(Switching times according to Sunset / Sunrise)
As UP-start time(s) or DOWN-start time(s) you find proposals of day-
times for Sunrise or Sunset
With the PLUS / MINUS buttons you may change this as you need (+/- 2 hours)
The Astro-switching-times are calculated according to the set date
The Astro-switching-times shifts according to the annual path of the sun
Calculation origin of the Astro-switching-times: Central Germany
FASTPROGRAMMING =====================
FAST PROGRAMMING / MEMORYFUNKTION
Fast programming UP-TIME-COMMAND:
Press the PLUS-button for 4 seconds [UP-Command will be executed]
After pressing the UP-button 4 sec. and the TIME are flashing
RESULT: Current time is saved as “UP-start time, following the day time” for the
complete week
Keep on pressing the PLUS-button for further 4 seconds and
the TIME are flashing
RESULT: Current time is saved as “UP-start time, according to sunrise (Astro)”
for the complete week
FAST PROGRAMMING DOWN-TIME-COMMAND:
Press the MINUS-button for 4 seconds [DOWN-Command will be executed]
After pressing the DOWN-button 4 sec. and the TIME are flashing
RESULT: Current time is saved as “DOWN-start time, according to sunset (Astro)”
for the complete week
Keep on pressing the MINUS-button for further 4 seconds and
the TIME are flashing
RESULT: Current time is saved as “DOWN-start time, according to sunrise (Astro)”
for the complete week
ADDITIONAL NOTES TO FAST PROGRAMMING OF ASTRO SWITCHING-TIMES
Within the fast programming mode only logical astro switching times will be accepted!
Otherwise the symbolic DO NOT FLASH and the switching time will be stored
as a standard “UP-start time, following the day time”. Logical astro switching times are:
- Astro-UP-time in the morning or Astro-DOWN-time in the evening
- Astro switching times with a max. of ±120 min. offset to the current sunrise or sunset time
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Muller RC 18.14 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info