Bedienungsanleitung Multiplex Power Peak D7 EQ-BID - 30 8129 (Seite 25 von 92) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

628910

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Operating Instructions

Power Peak

D7 EQ-BID

Order No.

8129

9. USER SETTINGS MENU

Pressing the "STOP / ESC" button switches to the main menu for

entering user data. These settings are global, and not specific to

any particular memory.

10. CYCLE DATA MENU

If no charge or discharge process is active, pressing the "STOP

/ ESC" button switches to the menu for viewing the cycle data.

Here you can view all the data relating to a charge or discharge

process.

The battery capacity is displayed both in the Charge (C:) line and

the Discharge (D:) line. The "C" line also displays the highest

voltage of the battery while the "D" line shows the lowest battery

voltage.

Press the "+" or "-" button to view all the data of a cycle (max. ten).

Note:

To erase the data, switch the charger off, or define a new battery.

(user setup)

Language : English

Rest Time : 2 min

Safety Cut : OFF

Safety Time : 1 min

Capa Ct : OFF

Capa value : 100 mAh

Key Beep : ON

(user setting)

Buzzer : ON

InputLow :10.5V

Int. Temp. : 39°C

Reset : Reset

Version  :V1.00

Cycle data

No. Capacity Voltage

1C: 0mAh  11.358V

D: 0mAh  0.000V

2C: 0mAh  11.412V

D: 0mAh  0.000V

3C: 0mAh  0.000V

D: 0mAh  0.000V

11. MODE SELECT (CHARGE / DISCHARGE /

CYCLE)

Once all the charge / discharge parameters have been set, the

charge or discharge mode can be selected: hold the "START /

ENT." button pressed in for at least two seconds in the "Memory

name" menu. The screen display now changes, and you see a

menu for selecting the mode. The top line displays the essential

battery data. In the lower part of the upper screen you can set the

desired process.

To make a selection you must press the "+" or "-" button. To start

the process press the "START / ENT." button briefly. The following

charge processes are available for NiCd and NiMH batteries:

•Charge

•Automatic

•Discharge

•Re-peak

•Cycle

The following charge processes are available for Lithium and Lead

batteries:

•Charge

•Discharge

•Storage

•Fast-charge

•Balance

The example

alongside shows

the "CYCLE" pro-

cess; at this point

you can determine

the sequence of

the cycle, and the

number of cycles.

•C>D(charge/discharge)•D>C(discharge/charge)

(01) Memory name. .

NiMH 6-cell 2000 mAh

Cyclemode: D>C

Cycle : 1

Language

Menu language selection: English,

German, Italian and French

Pause

Pause setting between two cycles (1 - 60 min.).

This setting is only useful when charging NiCd /

NiMH batteries.

Time cut-off

If this function is active (ON), the process you

have started is interrupted when the set "time

limit" has elapsed, or when another cut-off

parameter is triggered, such as Delta-Peak,

final discharge voltage, etc. A corresponding

message is displayed.

Time limit

Time setting after which the process is stopped

automatically.Adjustmentrange:Off-720min.

Capacity cut-

off

If this function is active (ON), the process you

have started is interrupted when the set "capa-

city limit" is reached, or when another cut-off

parameter is triggered, such as Delta-Peak,

final discharge voltage, etc. A corresponding

message is displayed.

Capacity limit

Capacity setting after which a process is auto-

matically stopped. Adjustment range: 0.1 - 60

Button beep

Switch button beep on and off.

Buzzer

Switch melody on and off. The melody sounds

when a process is concluded, or to alert you to

an error.

Low voltage

At this point you can define the input level which

triggers a low-voltage alarm, e.g. in order to

protect a car battery used as power source

from becoming deep-discharged. Adjustment

range:10.3V-11.0V,variablein0.1Vincre-

ments.

Int. temp

Displays the internal temperature of the charger.

Reset

Selecting this point erases all the previously set

parameters, and restores them to the factory

default values. This is achieved by holding the

"START / ENT." button pressed in for at least

two seconds.

Version

Display of charger firmware version.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex Power Peak D7 EQ-BID - 30 8129 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info