Bedienungsanleitung Multiplex Power Peak D7 EQ-BID - 30 8129 (Seite 28 von 92) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

628910

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Operating Instructions

Power Peak

D7 EQ-BID

Order No.

8129

14.2 EQUALIZER DISPLAY

When a Lithium battery is being charged or discharged, the screen

of the Power Peak

D7 EQ-BID can display the voltage of the indi-

vidual cells: press the "START / ENT." button during the process

(charge, discharge). It is absolutely essential to connect the Lithium

batterytothechargerusingtheVoltageSensorlead.

This screen display provides an overview of the state of balance of

the battery as a whole. The lower illustration shows the display for

a three-cell pack; the individual battery cells are well balanced: the

voltagedifferenceis20mV.

The top line (Output:) shows the total battery voltage.

The next line down shows the minimum and maximum cell voltages

in the pack.

This is followed by a display of the individual cell voltages with a

resolutionof10mV.

This type of display provides a fast and very accurate overview of

the voltage of the individual cells.

Pressing the "START / ENT." button again calls up the graphic

display.

Graphic display:

 (DataView)

Main :11.39V

Max:3.81V

Min:3.79V

3.79V3.79V3.81V

0.00V0.00V0.00V

0.00V

15. SCREEN DISPLAYS AFTER A PROCESS

The end of a charge / discharge process is indicated by the on-

screen message "End: XXXX"; you will also hear a melody. The

screennowdisplaysalltheimportantdatafortheprocessjust

completed. Holding the "STOP / ESC" button pressed in for at least

two seconds resets the messages, and the main menu reappears.

15.1 TEXT DISPLAYS

The screen displays the current settings. As well as showing the

completed process in the first line, the second line shows the

reason for the cut-off as a flashing item. At the same time and

according to the programming and battery type, the following will

be displayed as flashing items.

•End:Charge

•End:Automatic

•End:Fastcharge

•End:Discharge

•End:Storage

•End:Re-peak

•End:Cycle

•End:Balance

NOTE:

Asalreadymentioned,thedisplayadjustsitselftothebatterytype

and the selected cut-off method. Since it is not possible to show

all the displays, it is necessary to analyse and interpret the text

which appears.

16. PROGRAMMING A BID CHIP OR KEY

As soon as a BID chip or key is connected to the charger, the

charger switches to BID mode for displaying or programming the

BID chip or key. If the beeper is active, you will hear a brief beep

at this point. The same applies if the charger is switched on with

a BID chip or key already connected. The picture below shows

this situation.

The screen displays the following data, which can be program-

med:

1st line: date (01/01/2014): here you can store the date for the first

time you use the battery.

2nd line: battery type, cell count, capacity, programmable.

3rd and 4th lines: charge current, discharge current, user-variable.

5thline:TVCvoltage:thiscanbechangedtemporarily,butcannot

be stored on the BID.

The BID chip / key is programmed using the method described for

the"Memoryname"menuonpage8.

Once you have entered the battery date, the values must be

BID EDIT (01/01/2000)

LiPo7.4V2000mAh

Chg Current : 2.0 A

dChg Current : 1.0 A

dChgVolt  :3.2V/C

TVCVolt  :4.20V

Save to BID

v (voltage curve)

11.46V   00:01:38

DurationActual voltage

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex Power Peak D7 EQ-BID - 30 8129 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info