726078
9
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
INSTALLATION MANUAL
Adjust the four panel hook screws to keep the panel
horizontal, and screw them up to the ceiling evenly. ( Refer to
Fig.5-10.3)
Regulate the panel in the direction of the arrow in Fig.5-10.4
slightly to fit the panel's center to the center of the ceiling's
opening. Guarantee that hooks of four corners are fixed well.
Keep fastening the screws under the panel hooks, until the
thickness of the sponge between the body and the panel's
outlet has been reduced to about 4~6mm. The edge of the
panel should contact with the ceiling well. (Refer to Fig.5-11)
4
5
6
Fasten the rope of installation cover on the bolt of the
installation cover. (Refer to Fig.5-14-left)
Press the installation cover into the panel slightly. (Refer to
Fig.5-14-right)
Malfunction described in Fig.5-12 can be caused by
inappropriate tightness the screw.
If the gap between the panel and ceiling still exists after
fastening the screws, the height of the indoor unit should
be modified again. ( Refer to Fig.5-13-left)
You can modify the height of the indoor unit through the
openings on the panel's four c orners, if the lift of the
indoor unit and the drainpipe is not influenced (Refer to
Fig.5-13-right).
Hang the air-in grill to the panel, then connect the lead
terminator of the swing motor and that of the control box
with corresponding terminators on the body respectively.
Relocate the air-in grill in the procedure of reversed order.
Relocate the installation cover.
Fig.5-10
Tubing joint
Outlet joint
Hook panel
Water-receiver
Swing Motor
Hook-bolt
Cross-screwdriver
Do not coil the wiring of the swing motor into the seal
sponge.
Install the panel
Align the swing motor on the panel to the tubing joints of the
body properly. ( Refer to Fig.5-10)
Fix hooks of the panel at swing motor and its opposite sides
to the hooks of corresponding water receiver. ( Refer to
Fig.5-10.1) Then hang the other two panel hooks onto
corresponding hangers of the body. ( Refer to Fig.5-10.2)
3
CAUTION
panel sponge
body
Ceiling
panel
panel foam1 air out
Fan panel foam 2
Loosen upper nut
Adjust lower nut
4 - m m 6
outlet foam
Fig.5-12
Fig.5-14
Fig.5-11
Fig.5-13
Installation cover’s rope
Tap Screw Slide the four sliders
in the corresponding
channel when installing
the cover
9
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für MundoClima MUCSR-H6 - Model 24 to 60 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info