Remove the Front Panel
Press button in the upper left corner , and then the front panel will be folded down.
AF button
(release button)
PWR button
7/MOD button
disc slot
SEL/VOL knob
9/ button
8/ button
LCD display
(eject button)
USB Port
AUX IN jack
6/DIR+ button
5/DIR- button
4/RDM button
3/RPT button
2/INT button
1/P AU button
BAND/LOUD button
0/DSP button
EQ button
T A button
PTY button
SCH/AMS button
RESET button
SD/SDHC/MMC slot
Do not attempt to modify the unit, modifying the unit may cause an accident.
Installation or servicing of the unit by persons without training and experience in
elect ronic equip ment a nd aut omoti ve acce ssori es may be dan gerou s and co uld
expose you to the risk of electric shock or other hazards.
Stop the ve hicle befor e carrying o ut any oper ation that c ould interf ere with you r
driving.
Keep the volume at a level which you could hear sounds from outside the vehicle.
Do not work in extremely high or low temperature. Be sure the temperature inside
the vehicle is between +60°C and -10°C before turning on your unit.
When replacing the fuse(s), the replacement must be of the same amperage as
shown on the fuse holder .
Do not block vents or radiator panels. Blocking them will cause heat to build up
inside and may result in re.
Using this unit without running the engine can result in battery drainage.
Use only in cars with a 12 volt negative ground.
After completing the installation and beginning to play the unit(including replacing
the battery), please remove the front panel at rst, and then press RESET button
on the base with pointed object (such as ball-point pen) to set the unit to initial sta-
tus.
Before you install the unit, remove absolutely the two transportation screws on top
of the unit.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
1 1.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
1 1.
M-1010 MR
GB - 1
User Manual
CAR RADIO CD/MP3
PLA YER WITH USB & SD
Please read the instruction carefully
before operating the unit.
PRECAUTIO NS
English
* Do not attempt to load more than one disc.
* Only 12cm discs are compatible.
* New discs may have some roughness around the edges. Before load such disc into
the player, use a ball-point pen or the like to remove any roughness from the edge of
the disc.
* If there is a scratch, dirt or ngerprints on the disc, it may cause tracking error. Before
playing, clean the disc with a clean cloth. Wipe the disc from the center out.
* Don’t store discs in places with high temperatures or high humidity , they can become
warped. After playing, store the disc in its case.
GB - 2
GB - 3
CON NECTI ON
1. Antenna socket
2. Line out Right (red)
3. Line out Left (white)
4. Output plug (male)
5. Output plug (female)
6. FUSE holder (15 A)
Caution!
- Make sure to connect the color coded leads according to the diagram. Incorrect con-
nections may cause the unit to malfunction or damage the vehicle’s electrical system.
- Make sure to connect the speaker (-) leads to the speaker (-) terminal. Never connect
the left and right channel speaker cables each other or to the vehicle body .
- Make sure all the connections are completely correct before turning on your unit.
Do not connect the ignition wire (red) and the battery wire (yellow), it may cause a short circuit,
even result in re.
1. Remove the outer trim frame.
2. Select a position where the screw holes of the mounting bracket supplied with the
car and the screw holes of the main unit become aligned (are tted).
3. T ighten the screws. And then fasten them to the car .
GB - 4 GB - 5
Install the front panel
Insert the panel into the housing and make sure the panel is properly installed.
Otherwise, abnormality occurs on the display or some keys will not function properly .
Note: Never put any objects into the front panel.
Remove the unit
1. Detach the front panel. (please refer to upper part)
2. T ake out the outer trim frame.
3. Insert the keys supplied to the unit at the both sides of the unit (shown as illustrated)
until they click. Pulling the keys and makes them to remove the unit from the dash-
board.
GB - 6
LOCA TION O F CONT ROLS
GB - 7
Notice on disc
Use such discs may cause malfunction or breakdown of the internal mechanism:
with large scratches; with irregular shape; cracked; with any cellophane tape or other
glue on it or with peeling off marks; with protection sheet; equipped with stabilizers, etc.
- Method 2 DIN Rear-mount (For Japanese car)
BASI C OPER A TI ON
T urning on/off the unit
Press PWR button to turn on the unit. Press this button again to turn off the unit.
Note: When the unit is off, press any key except to turn on the unit.
Selecting the mode
After the unit is on, press 7/MOD button to select different sourcing mode: Radio
CD USB SD/MMC AUX
UNPA CK YOUR UNI T
When you unpack your new car radio, make sure that you have removed all the acces-
sories and information papers:
Main unit
User manual
Accessories:
Install the unit
- Method 1: DIN Front-Mount
INS T ALL AND R EM OVE TH E UNI T
SOUN D FE A TURES
Setting the Sound:
Repeatedly press SEL/VOL knob to select the desired mode in the following order :
“BAS” (Bass) -> “TRE” (Treble) -> “BAL” (Balance) -> “F AD“ (Fader) ->“BEEP“ (BEEP
ON/OFF) -> “T A VOL“ (T A volume) ->”LOC” (local) ->”STEREO” -> “EON” (EON ON/
OFF) -> “VOL” (V olume). After selecting the desired mode, you can adjust the current
level by rotating the SEL/ VOL knob.
- BEEP: In Beep mode, rotate SEL/VOL to select “BEEP ON” or “BEEP OFF”, for cor -
responding BEEP status.
- EON: please refer to RDS operation.
Note: The unit will return to the previous mode after 5 seconds without key press.
Reset the unit
Operating the unit for the rst time or after replacing the car battery , you must reset
the unit. T o set the unit to initial status, press RESET button located on the base with
a pointed object. When some errors occur in display , you can also reset the unit, but it
will erase the clock setting and some memorized functions.
V olume adjusting:
T o incr ea se or d ec re as e th e s ou nd l ev el , ro ta te S EL /V OL k no b c lo ck wi se o r an ti -
clockwise.
Preset equalizer
When you are listening to pop music, classic music or rock music, use the equalizer to
adjust the sound quality . Repeatedly press EQ button to select different equalizer m ode
in following order: FLA T ->POP->ROCK->CLASS -> EQ off.
Switching Loudness On/off
Pre ss and hold BAN D/L OUD butto n unti l “LOU D ON” sho ws on displ ay to act iva te
LOUDNESS function. By this function, you can increase the low frequency , which can
improve sound sensitivity . Press and hold this button again until “LOUD OFF” to cancel
LOUDNESS function.
NOTE: It will return to normal play mode if no key is pressed within 5 seconds.
Information display
- In case a RDS station is received.
In radio mode: CT -> FREQ ->PTY ->PS
In CD (MP3 / WMA) mode: CD (MP3/WMA) -> CT -> FREQ -> PTY ->PS
- In case received station is not RDS.
In radio mode: CT -> FREQ -> NO PTY -> NO PS
In CD mode: CD -> CT -> FREQ -> NO PTY -> NO PS
Time display
Press 0/DSP button to show the current time on display .
Adjust time: Long press 0/DSP until clock time with ashing hour digits appears.
Then Press and button to adjust the hour value and press 0/DSP to conrm.
Then minute digits ash. Press and button to adjust the minute value and
press 0/DSP to conrm.
LINE OUT
PartA
Part
B
(G R EE N /B L AC K)
( V IO L E T / B L A CK )
(W H IT E /B L AC K)
+ +
+
-
-
(V I OL E T)
(G R AY )
+
+
-
(W H IT E )
+
(G R AY / BL A CK )
- -
-
+
- -
(G R EE N )
+
6 4 2 8
5 3 1 7
6 4 2 8
5 3 1 7
4-SPEAKERSYSTEM
RearLeft
Speaker
FrontLeft
Speaker
FrontRight
Speaker
RearRight
Speaker
GroundWire (Black)
+12V Accessory/Switch (Red)
Power Antenna/Amplifier Turn on (Blue)
+12V Constant Power Supply (Yellow)
FUS E hol der (1 5 A)
5
6
4
3
2
1
1 2 3 5 6
7
4
8 9
1 1
10
AR-3108 IB MUSE 001 REV0 GB.indd1 1 2011-8-23 10:09:35