Bedienungsanleitung NAD C 245 BEE (Seite 7 von 12) (Englisch)

493503

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

1 CHANNEL B SPEAKERS (applicable to CHANNEL B only): Connect the

right speaker to the CHANNEL B SPEAKERS terminals marked “R +” and “R-”

ensuring that the “R+” is connected to the “+” terminal on your loudspeaker

and the “R-” is connected to the loudspeaker’s “-” terminal. Connect the

terminals marked “L+” and “L-” to the left speaker in the same way.

In Bridge Mode, connect the single speaker to the terminals marked “R +”

and “L+” ensuring that the “L+” is connected to the “+” terminal on your

loudspeaker and the “R+” is connected to the loudspeaker’s “-” terminal.

2 BRIDGE MODE (applicable to CHANNEL B only): Set the BRIDGE

MODE switch to the “ON” position and connect the speaker to the

terminals marked “L +” and “R+” ensuring that the “L+” is connected to

the “+” terminal of your loudspeaker and the “R+” is connected to the

loudspeaker’s “ - ” terminal. Connect the input source to the CHANNEL

B IN sockets.

3 CHANNEL B (IN/OUT): Connect the output from a pre-amplier or

processor, such as a surround-sound decoder, to this set of CHANNEL

B IN sockets. Use a twin RCA-to-RCA lead to connect the left and right

“Audio Output” of the preamplier or processor to these CHANNEL B

input sockets.

CHANNEL B OUT is line level “loop through” output. The same level of

input signal at the CHANNEL B IN sockets is available at CHANNEL B

OUT sockets thereby allowing the same signal to be shared or passed

on to another amplier.

Always turn OFF the C 245BEE and other components in the system

before connecting or disconnecting anything to the CHANNEL B IN

sockets.

4 CHANNEL A (IN/OUT): Connect the output from a pre-amplier or

processor, such as a surround-sound decoder, to this set of CHANNEL

A IN sockets. Use a twin RCA-to-RCA lead to connect the left and right

“Audio Output” of the preamplier or processor to these CHANNEL A

input sockets.

CHANNEL A OUT is a line level “loop through” output. The same level

of input signal at the CHANNEL A IN sockets is available at CHANNEL A

OUT sockets thereby allowing the same signal to be shared or passed

on to another amplier.

Always turn OFF the C 245BEE and other components in the system

before connecting or disconnecting anything to the CHANNEL A IN

sockets.

5 BRIDGE MODE (applicable to CHANNEL A only): The C 245BEE

amplier can be congured to be MONO (Bridge Mode), more than

doubling its output power. This way, the C 245BEE can be used as

part of a high power stereo or home-theatre system, by connecting

additional power ampliers.

In BRIDGED MODE, the C 245BEE will produce approximately 70W into

an 8 ohm loudspeaker. In this mode, the amplier sections will react

as though the speaker impedance has been halved. Low impedance

speakers (under 8 ohms) are not recommended when using Bridge

Mode as these may cause the amplier’s thermal cut-out to operate if

played at high levels.

Set the BRIDGE MODE switch to the “ON” position and connect the

speaker to the terminals marked “L +” and “R+” ensuring that the “L+”

is connected to the “+” terminal of your loudspeaker and the “R+” is

connected to the loudspeaker’s “ - ” terminal. Connect the input source

to the CHANNEL A IN sockets.

NOTE

Do not connect anything to the Right Input socket when Bridge Mode is

selected.

IDENTIFICATION OF CONTROLS

REAR PANEL

1 2 5 6 7 8 9

3 4

ATTENTION!

Please make sure that the C 245BEE is powered OFF or unplugged before making any connections. It is also advisable to power-down or unplug all

associated components while making or breaking any signal or AC power connections.

1110

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 245 BEE Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 245 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info