745051
1
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
© NAD CI 16-60
®
CI 16-60 Multi-Channel Amplier
Quick Setup Guide
GUIDELINE FOR NETWORK SETUP CONNECTION
This guideline is applicable to PC, MAC or smartphone control devices. Adapt the guidelines according to your
control device.
1 Use an Ethernet cable (not supplied) to connect CI 16-60’s LAN port to your Wired network or router.
IMPORTANT NOTES
For wired connection to be established, ensure that a broadband router that supports Ethernet is setup and
available.
Ensure that CI 16-60 and the control device (PC, Mac or smartphone device) are connected to the same network.
Use the information in the rear panel MAC ID sticker to identify the CI 16-60 from your network.
2 Power up your CI 16-60. The CI 16-60 will not communicate with the network when in Eco standby mode.
3 Use any network IP scanner to nd your CI 16-60’s Network ID (listed as the product name (NAD CI 16-60)
immediately followed by the last six digits in the MAC (Machine Access Control) address
(example: NAD CI16-60_123456). Note also the corresponding IP address assigned by the network.
4 Type the IP address into your control devices web browser to access your CI 16-60’s User Interface (UI).
5 Congure your CI 16-60’s Identication, Input/Output and Settings parameters via User Interface.
FIRMWARE UPGRADE PROCEDURE
1 Upon gaining access to your CI 16-60’s User Interface, check immediately for any rmware update by selecting
“Check For Updates” from the “Settings” tab.
2 Follow the rmware upgrade prompt instructions to complete the upgrade process.
POWER OPTIONS
SETTING DESCRIPTION
Power button Press power button to set unit to operating or standby mode.
Always On
Unit is always in operating mode. Shut down power by disconnecting unit’s AC plug from the mains power
source.
12V Trigger
Presence or absence of +12V DC supply from compatible devices to rear panel +12V TRIGGER IN will remotely
switch the unit to operating or standby mode.
Signal Sense
Unit will instantaneously turn from standby to operating mode if it senses any input signal (approximately
above 2 mV RMS input) applied through any of the GLOBAL or LINE INPUT sockets.
IMPORTANT
CI 16-60 factory default setting for Eco Mode is ON. With “Power Mode” set to “Signal Sense” and “Eco Mode” set
to “ON”, CI 16-60 will automatically go to Eco standby mode after 20 minutes of no active audio source input.
nadelectronics.com/product/ci-16-60-multi-channel-amplier
support.nadelectronics.com
AUDIO OUT
L
R
© NAD CI 16-60
1.
© NAD CI 16-60
x1
© NAD CI 16-60
2 CHANNEL AUDIO OUT
UNBALANCED
R BALANCED L BALANCED
L
R
x1/x2/x3...x8
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
MODEM USBLAN 4
LAN 3LAN 2LAN 1
DISPLAY USB USB
x8 x1 x1 x4 x4
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für NAD CI 16-60 DSP wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info