Bedienungsanleitung NAD M27 (Seite 5 von 12) (Englisch)

745043

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

INTRODUCTION

GETTING STARTED

WHAT’S IN THE BOX

Packed with your M27 you will nd

• A detachable mains power cord

• Four pieces of magnetic feet

• USB ash drive

• Cleaning cloth

• Quick Setup Guide

NOTE

Connect supplied USB ash drive to any compatible device to view the

M27 owner’s manual and Quick Setup Guide.

QUICK SETUP GUIDE

In case you simply cannot wait to experience the performance of your

new NAD M27 Seven Channel Power Amplier, the following QUICK SETUP

GUIDE is recommended to help you get started.

Ensure that the M27 is unplugged before making any connections. It is

also advisable to power-down or unplug all associated components while

making or breaking any signal or AC power connections.

1 Set the external source's volume control to minimum level. External

source can be a preamplier, processor, amplier or any applicable

device.

2 Set SELECT switch to BALANCED or SINGLE-ENDED. Connect the analog

audio output of your external source to the M27 rear panel’s BALANCED

or SINGLE-ENDED analog audio input. Depending upon the source’s

conguration, analog audio input connection can be made up to seven

channels either via BALANCED or SINGLE-ENDED input ports.

3 Connect your speakers to the SPEAKER terminals of M27. Note

suggested speaker connections as reected in the rear panel channel

allocations.

4 Plug-in to a mains power source the M27’s supplied mains power cord.

Connect corresponding end of the mains power cord to the AC mains

input of M27 and the plug connected to a mains power source.

5 Plug-in also to a mains power source the external source’s mains power

cord. Power up the external source ahead of the M27.

6 Set to ON the rear panel POWER switch of M27. The M27 goes to

standby mode as shown by the amber status condition of the Power

indicator.

7 Press (Standby) button for the M27 to be switched ON from standby

mode. The Power indicator will turn from amber to bright/white color.

The M27 is ready for operation.

8 Adjust the external source’s volume control according to desired

listening level.

SAVE THE PACKAGING

Please save the box and all of the packaging in which your M27 arrived.

Should you move or otherwise need to transport your M27, this is by far the

safest container in which to do so. We’ve seen too many otherwise perfect

components damaged in transit for lack of a proper shipping carton, so

please: Save that box!

NOTES ON INSTALLATION

• Your NAD M27 should be placed on a rm, level surface.

• Avoid placing the unit in direct sunlight or near sources of heat and

damp.

• Allow adequate ventilation.

• Do not place the unit on a soft surface like a carpet.

• Avoid placing the M27 inside a closed cabinet that is not well ventilated

as this may compromise the M27’s performance and reliability.

• Ensure that the M27 is unplugged before making any connections.

• For best performance, use quality speaker leads of 16 gauge (1.5mm

)

thickness or more.

• If the unit is not going to be used for some time, disconnect the plug

from the mains power source.

• Use a dry cloth for cleaning.

DO NOT REMOVE THE COVER; THERE ARE NO USERSERVICEABLE

PARTS INSIDE.

BARE WIRES AND PIN CONNECTORS

WARNING: The terminals marked with this symbol

are hazardous live. External wiring connected to these

terminals requires installation by an instructed person or

the use of ready-made leads or cords.

Bare wires and pin sockets should be inserted into the hole in the shaft

of the terminal. Unscrew the speaker terminal’s plastic bushing until the

hole in the screw shaft is revealed. Insert the pin or bare cable end into

the hole and secure the cable by tightening down the terminal’s bushing.

Ensure bare wire from the speaker cables does not touch the back panel or

another socket. Ensure that there is only 1/2” (1cm) of bare cable or pin and

no loose strands of speakers wire.

FEET INSTALLATION

The supplied magnetic feet can be easily installed by aligning and attaching

them to their corresponding foot shoe. Refer to illustration below.

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M27 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M27

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info