Bedienungsanleitung NAD M3e (Seite 15 von 20) (Englisch)

602914

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

FRANÇAISDEUTSCHNEDERLANDSESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

M3 REMOTE CONTROL HANDSET (FIGURE 3)

The Remote Control handset handles all the key functions of the M3 and has additional

controls to remotely operate both NAD DVD and CD machines (see CD/DVD Switch below).

It will operate up to a distance of 16ft (5m). Alkaline batteries are recommended for maximum

operating life. Two AA (R6) batteries should be fitted in the battery compartment at the back

of the Remote Control handset. When replacing batteries, check that they have been put in

the right way round, as indicated on the base of the battery compartment.

Please refer to previous sections of the manual for a full description of individual functions.

When a command from the remote control is received, the Status Condition L.E.D. will blink.

ON/OFF: The ON/OFF buttons turn on and to standby the M3. These buttons will only

function when the Status Condition LED is either blue representing the on-state, or amber

representing the standby state.

To turn on the second zone output, first enable the REC/Z2 button (3) as shown by the

red LED beside the REC/Z2 button, then press the ON button. To turn off the second zone

output, enable the REC/Z2 button, then press the OFF button. For further explanation of

the second zone output controls, see REC/Z2 button below.

2. Source Buttons: There are 7 source buttons as well as a REC/Z2 button. For direct input

selection, press the appropriate input button.

3. REC/Z2: Select this button to switch the remote control to a second zone remote control.

The Source Buttons for the second zone will be active as shown by the red LED beside the

REC/Z2 button. There is a 3 second window for selecting a source before this button times

out. Select the source within this duration.

4. SPEAKERS A & B: Select to enable either speaker A, B or both A & B.

5. MODE: Press the MODE button to toggle through the four listening modes. A press

longer than one second will advance the mode selection to the next state as follows;

STEREO, MONO, LEFT, RIGHT, and then return to the STEREO listening mode. Release the

MODE button to stop the sequence.

6. MUTE: Press the MUTE Button to temporarily switch off the sound to the speakers. The

word MUTE will continuously display in the VFD. Press MUTE again or the volume control

to restore sound. The mute function does not affect recordings made using the REC/Z2

output but will affect the signal going to both Preamp outputs.

7. VOL (Volume): Press the VOL or buttons to respectively increase or decrease

the loudness level. Release the button when the desired level is reached. The VFD on the

front panel will indicate the level set. The Master Volume buttons do not affect recordings

made using the REC/Z2 outputs but only affect the signals going to the Preamp outputs.

8. BALANCE: Press the balance button once and then within 5 seconds, press the VOL

or buttons respectively to adjust the either the LEFT or RIGHT balance level. After

about 5 seconds, the balance menu will switch off saving the balance settings in memory.

9. TONE: Press the TONE button to activate or deactivate the tone controls. Release the

TONE button to stop the sequence. To bypass bass, treble, and spectral tilt controls

completely, select TONE DEFEAT (direct bypass of all analogue filters).

Selecting TONE ACTIVE allows one to adjust the bass, treble, and spectral tilt settings of

the M3 by pressing the VOL or buttons respectively. Bass and treble levels are

adjustable between +/- 5dB. The spectral tilt adjustment allows for simultaneous +/-3dB

bass and treble offsets. When adjusting bass and treble levels, the spectral tilt value will

remain 0dB. When adjusting the spectral tilt, the bass and treble values will follow the

spectral tilt adjustment simultaneously.

About the M3 Dual Mono Integrated Amplifier

Operation

M3 10262005.qxd 1/3/2006 2:50 PM Page 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M3e Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M3e

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info