Bedienungsanleitung NAD M50.2 (Seite 8 von 12) (Englisch)

745045

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

1 ANALOG AUDIO INPUT

• Input for line level sources such as CD player, tuner or any

compatible devices. Use a twin RCA-to-RCA lead to connect the

source device’s left and right “Audio Output” to this input. The source

will appear as an Analog Input in the navigation drawer of the BluOS

Controller App.

2 WIFI ANTENNA TERMINAL

• Connect supplied wireless antenna to this WIFI antenna terminal.

3 DIGITAL AUDIO

COAXIAL IN, OPTICAL IN

• Connect to corresponding optical or coaxial digital audio output

of sources such as CD or BD/DVD players, digital cable box, digital

tuners and other applicable components. The source will appear

as an Optical Input or Coaxial Input in the navigation drawer of the

BluOS Controller App.

COAXIAL OUT, OPTICAL OUT

• Connect to corresponding optical or coaxial digital audio input

of compatible devices such as receivers, computer soundcards or

other digital processors.

4 HDMI OUT

• Connect to compatible devices with HDMI input.

• Connected display device will show similar image or information

reected in the touch panel display.

IMPORTANT NOTE

HDMI OUT does not support I2S DACs.

5 RS 232

• Use an RS232 straight through serial cable (not supplied) to

interface this port to the corresponding RS232 port of another

equipment like the NAD M12, NAD M32 or any compatible NAD

models. Through this RS232 connection, the VOLUME slider in the

App can be adjusted to increase or decrease the audio output level

of the M50.2.

6 USB 1, USB 2 (Type A)

• Connect USB mass storage device to any or both of these USB Type

A input terminals.

• Typical USB mass storage device compatible with M50.2 include

portable ash memory devices and external hard drives (FAT32

recommended).

• A notication will be shown in BluOS Controller App if a USB

device is inserted. Click on USB in the navigation drawer to browse

content.

7 LAN

LAN connection must be setup for wired connection to be established.

Set up a Wired Ethernet broadband router with broadband internet

connection. Your router or home network should have a built-in DHCP

server to consummate the connection.

• Using a standard straight-through Ethernet cable (not supplied),

connect one end of the Ethernet cable to the LAN port of your

wired Ethernet broadband router and the other end to M50.2’s LAN

port.

8 SERVICE/USB

• This is not for consumer use. Only authorized service personnel can

access this USB port and SERVICE button.

• USB (Type B) port and SERVICE button are for servicing purposes

only.

9 BT (BLUETOOTH) ANTENNA TERMINAL

• Connect supplied wireless antenna to this BT antenna terminal.

IDENTIFICATION OF CONTROLS

REAR PANEL

OUT

CAUTION:

REPLACE WITH SAME TYPE T2AL 250V FUSE

ATTENTION:

UTILISER UN FUSIBLE DE RECHANGE

DE MEME TYPE DE T2AL 250V

4 5 6 8 10

1 2 7 9 11 12 13 14

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M50.2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M50.2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info