493498
40
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
LEARNING CODES FROM OTHER REMOTES
Begin by positioning the HTR 8 nose-to-nose” with the source remote so
the two devices’ infrared windows are about 2 inches apart.
• Enter Learning Mode: On the HTR 8, simultaneously press-and-hold for
3 seconds both a Device Selector key and the [RES] key until the Learn
LED (located between HTR 8’s ON and OFF buttons) turns steady green.
• Press the HTR 8’s function key you wish to teach a command; the Learn
LED will turn amber.
• Press-and-hold the function key on the source remote: The HTR 8’s
Learn LED will icker amber for a second or two, then turn solid green.
The command is learned.
• Press the HTR 8’s Device Selector key again to exit the learning mode.
If the Learn LED does not icker amber you may need to vary the distance
between the remotes. If the Learn LED turns red rather than green, that
particular command of that source remote command could not be learned.
Example: Learning “DVD Pause”
Position the HTR 8 and your DVD players remote as described above.
• On the HTR 8, simultaneously press-and-hold [DVD] and [RES]; the Learn
LED turns steady green.
• Press the HTR 8’s Pause [ ] key; the Learn LED turns amber.
• Press-and-hold the corresponding Pause key of your DVD player’s
remote control; the HTR 8’s Learn LED ickers amber and then turns
solid green. The command is learned.
• Press [DVD] again to exit the learning mode.
NOTES
• TheHTR8canlearnupto360commandsmakinguseofalltheDEVICE
SELECTOR and function keys.
• TheDEVICESELECTORkeyscanthemselvesbeconguredtolearna
command.
• PressandholdaconguredDEVICESELECTORforatleast2secondsto
execute a function assigned to the particular DEVICE SELECTOR key.
• ShortpressofaconguredDEVICESELECTORwilljustswitchtheactivedevice.
CANCEL OPERATION
You can cancel conguring a key, by pressing the active Device Selector key
before the learn process is complete; the Learn LED will turn red.
PUNCH THROUGH
The HTR 8’s “punch-through function allows you to retain a function key
from one Device Select “page to another, so that, for example, the AMP
[SURR MODE] function might still control the T 187 when the DVD Device
Selector page is active.
NOTE
The HTR 8’s [VOL D/F] keys are pre-programmed as “punched-
through” for all Device Selector pages: [VOL D/F] will operate the
T187’s master-volume regardless of the currently selected device. The
[SURR][CENTER,]and[SUB]ChannelVolumecontrolssimilarlyarepre-
programmed as punched-through.
To set a punch through, after entering the Learning Mode, and pressing the
desired key to be punched through, simply press the device key twice of
the device to punch through to. The status LED will turn green; press the
Device Selector key again to exit Learning Mode.
Example: Punch-through AMP [SURR MODE] key to the DVD “page”
• On the HTR 8, simultaneously press-and-hold [DVD] and [RES]; the Learn
LED turns steady green.
• Press [SURR MODE]; the Learn LED turns amber.
• Press [AMP] twice; the Learn LED turns green.
• Press [DVD] again to exit the learning mode.
COPY A COMMAND FROM ANOTHER KEY
You may copy a command from any HTR 8 key to any other. To copy a key
function, after entering the Learning Mode, and pressing the desired key to be
copied to, simply press the device key from which you wish to copy, having rst
pressed its Device Selector key if it resides on another “page. The status LED will
turn green; press the Device Selector key again to exit Learning Mode.
Example: Copy the Pause command from the CD page to the AMP [ ]
button:
• On the HTR 8, simultaneously press-and-hold [AMP] and [RES]; the Learn
LED turns steady green.
• Press Pause [ ] ; the Learn LED turns amber.
• Press [CD]; press Pause [ ] ; the Learn LED turns green.
• Press [AMP] again to exit the learning mode.
NOTE
The copy and punch-through functions are similar. However, if you copy a
command and then subsequently delete, or over-write the original (source-
key) command , the copied-to key’s command remains unchanged. If you
punch-through to a command and then delete or over-write the original
key, the punched-through functions also change accordingly.
MACRO COMMANDS
A “macro” command is a series of two or more remote codes issued
automatically from a single keypress. You might use a macro to automate
a simple command sequence, such as, Turn on the DVD player and then
press PLAY”. Or you might compose an elaborate macro to power up an
entire system, select a source, choose a Listening Mode, and begin playback
– again, all from a single keypress. Each DEVICE SELECTOR and function key
of the HTR 8 can store one macro.
NOTE
Macros are independent of the currently selected device.
RECORDING MACROS
To record a macro, simultaneously press-and-hold for 3 seconds both the
[MACRO] key and the HTR 8 function key to which you wish to assign the
macro, until the status LED turns green. The macro button will also light up.
Press the sequence of function keys to be recorded into the macro, being
sure to rst press the requisite Device Selector key for each function (you
may switch devices while recording the macro as many times as necessary),
allowing you to create macro containing commands from more than one
Device Selector “page.
When you have nished entering the desired command sequence, press
[MACRO] again to store the macro; the Learn LED and [MACRO] key
illumination will turn o.
NOTE
Each macro can store a maximum of 64 command steps. If you exceed
this number, the macro will be stored automatically after the 64th
command is added.
Example: Record a Macro to the [0] key to Turn on the T 187, Select
“Input1” (Source 1), and Commence Playback of connected Source 1 device
(as in DVD player):
• On the HTR 8, simultaneously press-and-hold [MACRO] and [0] (numeric
zero); the Learn LED turns steady green.
• Press [AMP]; press [ON]; press [1] (“Input or Source 1”); press [DVD]; press
[ ] (Play) - the Learn LED blinks as each step is added.
• Press [MACRO] again to exit the macro-record mode.
To clear a macro, perform the above steps without entering any functions.
OPERATION
USING THE HTR 8 REMOTE CONTROL
40
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ
40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für NAD T 187 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von NAD T 187

NAD T 187 Bedienungsanleitung - Deutsch - 48 seiten

NAD T 187 Bedienungsanleitung - Holländisch - 48 seiten

NAD T 187 Bedienungsanleitung - Französisch - 48 seiten

NAD T 187 Bedienungsanleitung - Italienisch - 48 seiten

NAD T 187 Bedienungsanleitung - Spanisch - 48 seiten

NAD T 187 Bedienungsanleitung - Schwedisch - 48 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info