Bedienungsanleitung NAD T 754 (Seite 29 von 32) (Englisch)

606564

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

2929

ENGLISH

USING THE HTR 2 REMOTE CONTROL

TRIGGER SETUPTRIGGER SETUP

TRIGGER SETUP

USING THE ZR 2 REMOTE CONTROLUSING THE ZR 2 REMOTE CONTROL

USING THE ZR 2 REMOTE CONTROL

Search Mode

If none of the codes from the table, when entered, turns on the component, and if you are quite sure you

have followed the above procedure completely and carefully, you may want to try the “search” method as

follows:

Enter Library Mode by simultaneously pressing-and-holding for 3 seconds both the desired Device Selector

key and the [A/V PRESET] key, until the Learn LED turns green. Now press-and-hold the HTR 2’s [

] (or

[

]) key; the remote will step through all the available codes at a rate of approximately 1 per second. When

the component turns off, immediately release the cursor key; press [ENTER] to accept that code-library and

exit the Library Mode. Try a few commands; should you prove to have stepped past the needed code-library,

re-enter the Library Mode and use the cursor key to step back to it.

NOTE: It is possible that search mode will find code-libraries that operate, at least partially, some other-

brand (non-NAD) components. You may certainly exploit such capabilities as you find them. However,

since we can only ensure the completeness or accuracy of NAD code-libraries, we cannot support the HTR

2’s operation with other-brand components.

Checking Code-Library Number

You can check the current code-library on any Device Selector key as follows. Enter Library Mode by

simultaneously pressing-and-holding for 3 seconds both the desired component’s Device Selector key and

the [A/V PRESET] key, until the Learn LED turns green. Press the [DISP] key; the HTR 2 indicates the current

code-library by flashing its [TAPE], [VCR], and [MACRO] keys. For example, to indicate code-library #501 the

HTR 2 will flash [TAPE] 5 times, pause, and then flash [MACRO] once. You might wish to make a note of your

components’ code-library numbers.

SUMMARY OF HTR 2 MODESSUMMARY OF HTR 2 MODES

SUMMARY OF HTR 2 MODES

Mode Keys To Press (for 3 seconds)

Learn/Copy/Punch Through Device Key + Record Key

Delete Mode Device Key + Return Key

Macro Record Macro Key + Function Key

Library Mode Device Key + Preset Key

Back Light Timeout Display Key + Digit Key

Factory Reset (see “Factory Reset,” above)

The ZR 2 remote control is a discrete compact remote for controlling the T 754 from various rooms other than

the main room. The ZR 2 remote allows full separate control of the source selection irrespective to the main

room. This means the zone input may be completely different, audio and video, from the main input and

thus corresponding volume levels as well. If one wishes to enjoy the same source, as the main room the ZR

2 remote has a [LOCAL] button to allow simultaneous listening, but with full separate volume levels.

The T 754’s front florescent display will show activity of the zone control so that main room occupants are

aware of the zone remote activity. Furthermore if there is no main room activity, only the zone indicator will

be active in the T 754’s fluorescent display.

The T 754’s rear-panel TRIGGER output can be assigned to any of its six AV inputs: DVD, SAT, VCR, VIDEO

4-6. Whenever the assigned input is selected, either manually or by recalling a Preset, the TRIGGER output

will produce +12 V DC, which can be used to activate a connected component or system. See your NAD

audio specialist for more information.

ASSIGNING THE TRIGGER OUTPUTASSIGNING THE TRIGGER OUTPUT

ASSIGNING THE TRIGGER OUTPUT

From the OSD’s main <Setup> menu, select the <Input Settings> item using the remote's [/] and

[

/] keys. One can select the video input (DVD, SAT, VCR, or VIDEO 4-6) you wish to assign to the

TRIGGER 1 output. Select <Save and Exit> to store the trigger assignment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 754 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 754

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info