Bedienungsanleitung Naim NAP 200 DR (Seite 4 von 44) (Englisch)

707507

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

3 General Installation

Naim equipment is designed to offer the finest

performance possible avoiding compromise

wherever practical. This can lead to circumstances

that may be unfamiliar. The notes that follow contain

advice specifically related to Naim equipment

as well as more general warnings about the use

of domestic audio products. Please read them

carefully.

3.1 Siting The Equipment

In order to reduce the risk of hum audible from the

loudspeakers, power supplies and power amplifiers

should be located a reasonable distance away from

other equipment. The maximum separation distance for

connected equipment is that allowed by the standard

interconnect lead.

Some Naim equipment is extremely heavy. Check the

weight of the equipment prior to lifting and if necessary

use more than one person so that it can be moved safely.

Ensure that your equipment rack or table can easily

support the weight and is stable.

Some speakers and stands are intended to be used with

floor spikes fitted. Care should be taken when siting and

moving them to avoid personal injury or damage to

cables and surfaces. Floor protectors are available from

your local dealer or distributor to protect non carpeted

floors.

3.2 Switching On

Source components and power supplies should be

switched on before the power amplifiers. Always switch

amplifiers off and wait a minute before connecting or

disconnecting any leads. Always use the power switch on

the product rather than a mains outlet switch.

A “thump” may be heard from the loudspeakers as power

amplifiers are switched on. This is normal, will not cause

any loudspeaker damage and does not point to any fault

or problem. A mild “pop” may also be heard shortly after

equipment is switched off.

3.3 Running In

Naim equipment takes a considerable time to run in

before it performs at its best. The duration varies, but

under some conditions the sound may continue to

improve for over a month. Better and more consistent

performance will be achieved if the system is left switched

on for long periods. It is worth remembering however that

equipment left connected to the mains can be damaged

by lightning.

3.4 Radio Interference

In some circumstances, depending on where you live

and the earthing arrangements in your home, you may

experience radio frequency interference. Controls on

broadcasting in some territories allow very high levels of

radio frequency radiation and both the choice and exact

siting of equipment may be critical. Susceptibility to radio

frequency interference is related to the wide internal

bandwidth necessary for high sound quality. A radio

frequency filter kit is available for some Naim equipment

but sound quality will be progressively compromised as

more elements of the kit are fitted.

3.5 Lightning Precautions

Your Naim hi-fi system can be damaged by lightning

and should be turned off and disconnected from the

mains when there is risk of lightning strike. For complete

protection all mains plugs and any aerial cables should be

disconnected when not in use.

3.6 Problems?

Consumer protection varies from country to country. In

most territories a retailer must be prepared to take back

any equipment he has sold if it cannot be made to work

satisfactorily. A problem may be due to a fault in the

system or its installation so it is essential to make full use of

your dealer’s diagnostic skills. Please contact your local

distributor, or Naim Audio directly, if any difficulties cannot

be resolved.

Some Naim equipment is made in special versions for

different territories and this makes it impracticable to

arrange international guarantees. Please establish the

local guarantee arrangements with your retailer. Contact

Naim Audio directly for help and advice if necessary.

3.7 Service and Updates

It is essential that repairs and updates are only carried

out by an authorised Naim retailer or at the factory by

Naim itself. Many components are custom made, tested

or matched and appropriate replacements are often

unobtainable from other sources.

Direct contact to Naim for service or update information

should be made initially through Customer Services:

Tel: +44 (0)1722 426600

Email: info@naimaudio.com

Please quote the product serial number (found on its rear

panel) in all correspondence.

Introduction

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim NAP 200 DR Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim NAP 200 DR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info