Bedienungsanleitung Naim UnitiServe (Seite 6 von 31) (Englisch)

707496

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

Installation - Getting Started

2 Getting Started

UnitiServe should be installed horizontally on a dedicated equipment stand intended

for the purpose. Do not stand UnitiServe directly on top of another item of equipment.

UnitiServe should be installed in its final location before connecting cables or switching

on.

UnitiServe can be connected to a computer network to retrieve album data and artwork

from the internet, to stream music around the home using NaimNet hardware, or to take

advantage of one of its alternative user interfaces. If UnitiServe is to be used in a network

it is important that the network is working when UnitiServe is connected and switched on.

Locally connected audio amplifiers should not be switched on before UnitiServe is

switched on. The UnitiServe power switch is located on the rear panel.

To begin installation first identify the rear panel network, audio output and power input

sockets, and connect the appropriate cables.

2.1 Internet/Network Connections

While UnitiServe can be used in “stand-alone” mode

without any network connection, if its full capabilities are

to be realised it requires connection to an “always on”

internet service via an ethernet router/modem with a built-

in firewall.

If UnitiServe is to be used in a NaimNet/StreamNet network

audio system, the network connection also enables

UnitiServe to communicate with other network devices and

provides access to its alternative user interfaces.

UnitiServe is set up when originally shipped not to require

any further network configuration but to connect to a

network automatically (it uses DHCP by default). However,

if your UnitiServe has been previously used, its network

configuration may have been altered leaving it unable to

connect automatically. Contact your retailer, installer or

Naim Audio directly if this appears to be the case.

Note: A UnitiServe used in stand-alone mode and switched

on without a working network connection will revert to

an internal IP address only suitable for stand-alone use.

To restore the default DHCP setup, switch UnitiServe off,

connect the network and switch it on again.

2.1.1 Network Hardware

Conventional ethernet network connection is strongly

recommended for the most consistent and secure

UnitiServe operation.

Ethernet-over-mains hardware may be used and provides

a simple and convenient method of home network

connection. However, depending on mains wiring factors

specific to each home environment, the presence of

network data on the mains supply may compromise

overall system sound quality. If any sound quality

compromise is found to be unacceptable, dedicated

network cabling should be installed.

2.2 Power Supply Connection

UnitiServe is powered by an external power supply.

Connect the output cable of the power supply to the

UnitiServe power input socket and the mains input cable

of the power supply to a mains outlet socket. Use only the

mains cable supplied.

2.3 Audio Connection

Connect one of the UnitiServe digital audio output sockets

(BNC coaxial or TosLink optical), to an appropriate audio

system digital input. For best performance use a Naim DC1

digital coaxial interconnect cable.

2.4 Switch On

If UnitiServe’s network facilities are to be used ensure that

it is connected to a working internet connection before

switching it on and that all the necessary peripheral

equipment is appropriately connected and configured.

Switch on UnitiServe using the rear panel power switch.

Note: If UnitiServe is to be switched on from shutdown mode,

the power switch must be switched off and on again. See

Section 2.8 for more on shutdown mode.

After approximately one minute, during which the front

panel logo will flash, the user interface Home menu will

appear on the interface display. Navigation around the

interface will depend on the interface hardware chosen.

If using a touch screen, touch the interface graphics to

select items. If using the web browser or external display

interface, select options using a keyboard/mouse or, if a

remote handset is employed, its navigation (3456), ok,

home and back keys.

Note: Ensure that the unit

has adequate ventilation.

The ambient temperature

in the vicinity of the unit

should not exceed 35°C.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Naim UnitiServe Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Naim UnitiServe

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info