Bedienungsanleitung Napoleon PTSS215PI (Seite 24 von 28) (Englisch, Französisch)

637928

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Wall Mounting Instructions:

1. Using the two holes provided in the vertical tube, mount the

bracket to the wall.

2. Ensure minimum clearance to combustibles are maintained, 4”

(100mm) to sides, and 6”(150mm) from the rear.

3. Do not locate the grill under unprotected combustible construction.

4.The platform may be swivelled by removing the two #8 x 3/8”

flathead phillips screws and turning the platform to the desired angle.

Replace the two screws and tighten.

5. Once the platform is located in the desired position, the grill can be

mounted:

a. Lock the lid of the grill closed with the latch.

b. Hold the grill by the handle with one hand, place the other hand under the grill in the

centre of the front tapered surface.

c. Place the grill bottom on the platform and slide it forward to engage the tab protruding from

the bottom of the grill. Ensure that the tab is properly engaged.

d. When the dimples on the bottom of the unit line up with the holes on the platform, the latch is

ready to be fastened.

6. Once the grill has been attached, thread the regulator (clockwise) into the regulator mount.

On tube burner version, lift the burner slightly to align it with the orifice. Tighten by hand.

7. To fasten the regulator locking bracket, locate it at the bottom back corner of the regulator mount and turn the regulator until the

gas inlet is aligned with the hole in the regulator locking bracket. Slide the locking bracket forward until the two tabs engage into the

slots on the regulator mount. Tap in firmly.

8. Attach the cylinder to the regulator by turning clockwise. (Be sure not to cross thread the cylinder.)

Trailer Ball Mounting Instructions:

1. Place the ball mount over the ball on your drawbar or bumper.

2.Tighten the two wing screws until the mount is firmly held in place.

3. Once the mounting arm is tight, the grill can be mounted:

a. Lock the lid of the grill closed with the latch.

b. Hold the grill by the handle with one hand, place the other hand

under the grill in the centre of the front tapered surface.

c. Place the grill bottom on the platform and slide it forward to

engage the tab protruding from the bottom of the grill. Ensure that the

tab is properly engaged.

d. When the dimples on the bottom of the unit line up with the holes on the

platform, the latch is ready to be fastened.

4. Once the grill has been attached, thread the regulator (clockwise) into the regulator

mount. On tube burner version, lift the burner slightly to align it with the orifice. Tighten

by hand.

5. To fasten the regulator locking bracket, locate it at the bottom back corner of the

regulator mount and turn the regulator until the gas inlet is aligned with the hole in the

regulator locking bracket. Slide the locking bracket forward until the two tabs engage into

the slots on the regulator mount. Tap in firmly.

6. Attach the cylinder to the regulator by turning clockwise. (Be sure not to cross thread

the cylinder.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Napoleon PTSS215PI Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info