Bedienungsanleitung Native Komplete Kontrol S-series MK1 (Seite 145 von 147) (Englisch)

707116

145

Zoom out

Zoom in

Vorherige Seite

1/147

Nächste Seite

• Display menu: Lets you select one of two ways to display the current state of the Modulation

Strip: Bar or Dot. Bar displays a bar of lit LEDs from the default position of the strip to the cur-

rent value; whereas Dot displays a dot of lit LEDs at the current value.

• Touch Ctl menu: Lets you select between Absolute (default behaviour) and Relative. When us-

ing Relative, the current value of the controlled parameter is preserved when you put your fin-

ger anywhere on the Modulation Strip. You can then move your finger up and down to change

the parameter by the corresponding amount.

Spring Mode

This mode simulates a simple spring that can be deflected both up and down from its default posi-

tion, which is the middle of the Modulation Strip. The current position of the spring (the parameter

value) is indicated by a blue LED. If you put your finger on the strip, the value instantly jumps to

the corresponding position and stays there as long as you keep your finger on the strip. When you

remove your finger, the value springs back to its default position. This behavior is called Absolute

(alternatively, Standard can be set to Relative, see below). This mode mimics the behavior of the

Pitch Strip. In Spring mode, the following additional settings are available for the Modulation Strip:

• Display menu: Lets you select one of two ways to display the current state of the Modulation

Strip: Bar or Dot. Bar displays a bar of lit LEDs from the default position of the strip to the cur-

rent value; whereas Dot displays a dot of lit LEDs at the current value.

• Strength slider: Adjusts the rate at which the spring rebounds to its default position. The higher

the Strength setting, the quicker the value will spring back to its default position.

• Touch Ctl menu: Lets you select between Absolute (default behaviour) and Relative. When us-

ing Relative, the current value of the controlled parameter is preserved when you put your fin-

ger anywhere on the Modulation Strip. You can then move your finger up and down to change

the parameter by the corresponding amount.

Ball Mode

This mode simulates a ball that is attracted by the gravity of your finger. The current position of the

ball (the parameter value) is indicated by a blue LED. If you put your finger on the strip, the ball will

move towards your finger and stop as it reaches the finger’s position. If you remove your finger

before, the ball sustains its momentum and continues to move along the Modulation Strip until the

friction of the surface causes it to slow down and stop. Alternatively, you can “throw” the ball by

putting your finger on the ball’s current position, dragging it in any direction, and removing your

finger. The faster you drag your finger, the faster the ball will get. In Ball mode, the following addi-

tional settings are available for the Modulation Strip:

• Display menu: Lets you select one of two ways to display the current state of the Modulation

Strip: Bar or Dot. Bar displays a bar of lit LEDs from the default position of the strip to the cur-

rent value; whereas Dot displays a dot of lit LEDs at the current value.

• Friction slider: Adjusts the friction of the surface that slows down the ball once you have re-

moved your finger. The higher the Friction value, the quicker the ball will decelerate and stop.

When fully left, the ball never stops. When fully right, the ball stops instantly.

• Gravity slider: Adjusts the attraction of your finger on the ball: The higher the Gravity value,

the faster the ball will move. This parameter doesn’t affect the ball movement if you throw the

ball with your finger (see above).

Configuring Touch Strips

139

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Native Komplete Kontrol S-series MK1 Seite 145

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Native Komplete Kontrol S-series MK1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info