Bedienungsanleitung Nestor Martin S33 (Seite 7 von 31) (Englisch)

571179

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

Draft Requirements

The appliance is merely one component of larger system. The other equally important component

is the venting system. This is necessary for achieving the required ﬂow of combustion air to the

ﬁre chamber and for safely removing unwanted combustion by-products from the appliance. If the

venting system’s design does not promote these ends, the system may not function properly. Poorly

functioning venting systems may create performance problems, as well as be a safety hazard

(i.e. an oversized chimney may result in less than optimum performance. Installations into a large

masonry chimney may require a liner to improve performance).

THE RECOMMENDED DRAFT REQUIREMENTS FOR YOUR STOVE IS NO LESS THAN -.04

AND NO GREATER THAN -.08. OPERATION OF YOUR STOVE WITH A DRAFT GREATER

THAN -.08 CAN POSSIBLY CAUSE DAMAGE TO THE STOVE AND VOID THE WARRANTY.

SPECIAL NOTE: A barometric damper is recommended for installations of stoves in areas that

may have high winds, which can affect the draft. The installation must be only in units with a newly

constructed chimney, free of creosote deposits. The barometric damper is an automatic device

designed to regulate the draft in a heating appliance, which in turn, stabilizes the chimney temperatures,

lessening the potential of over-ﬁring. Do not place the barometric damper greater than 24 inches (610 mm) above the

unit. Excessive draft will lead to poor control of the burn rate, possible over-ﬁring of the stove and damage to the cast

iron components of the ﬁrebox. Most barometric dampers are calibrated in inches of water column and can be set to

draft requirements of -.03 to -.08 inches (-7.5 to -20 Pa). It is recommended that the barometric dampers to be set

between -.05 and -.06 inches.

Chimney Height requirements

According to the American National Standards Institute ANSI/NFPA 211-92, draft 1-7, a chimney or vent shall be so

designed and constructed to develop a ﬂow sufﬁcient to completely remove all ﬂue and vent gases to the outside

atmosphere. The venting system shall satisfy the draft requirements of the connected appliance in accordance with

the manufactures instructions.

The “3-foot, 2-foot, 10-foot rule” on chimney height states that a chimney must be:

1. At least 3 feet higher than the highest part of the roof opening through which it passes,

2. and at least 2 feet higher than any part of the roof within 10 feet, measured horizontally.

Due to prevailing winds, local terrain, adjacent tall trees, a hill or ravine near the home, or adjacent structures,

additional chimney height or a special chimney cap may be required to assure optimum performance.

.02

.01

.03

.04

.05

.06

.07

.08

.09

.05

1.0

IN. OF WATER DRAFT OR PRESSURE - LOW RANGE

IN. OF WATER DRAFT OR PRESSURE - HIGH RANGE

Draft gauge

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nestor Martin S33 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nestor Martin S33

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info