Bedienungsanleitung Netgear Arlo FlexPower Base Station VNB4000 (Seite 1 von 2) (Englisch)

681368

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

FlexPower Base Station for

FlexPower ONVIF Cameras

Model VNB4000-111PAS

Package Contents

Base station

Power cord

(localized to the region)

Note: For the ceiling and wall installation kit, see the other side of this

document.

Ethernet cable

Step 1: Install the Base Station

1. Use an Ethernet cable to connect the base station to a router or switch.

2. Connect the power cord that came in the package to the base station

and plug it in to an electrical outlet.

3. Press the Power button on the rear of the base station.

After the base station boots, the Power LED and the Network LED light

solid green.

Step 2: Sync Your Cameras to the Base Station

1. Make sure that the rechargeable battery is installed in the camera and

the camera is powered on.

For information about how to install the camera battery, see the quick

start guide that came with the camera.

2. Place the camera 2 to 4 feet (60 to 120 cm) from the base station.

3. On the base station, press the SYNC button.

The camera LED on the base station begins blinking green. This indicates

that the base station is attempting to pair with a camera.

4. On the camera, press the SYNC button.

The camera LED blinks blue. This indicates that the camera is attempting

to pair with the base station.

When the camera is paired to the base station, the camera Sync LED

blinks blue rapidly and then the camera LED on the base station lights

solid green.

5. Repeat Steps 1–4 to pair more cameras to the base station, if desired.

6. Move the cameras to the desired locations.

Step 3: Initial Setup

During initial setup, your computer or mobile device must be connected to

the same LAN as the base station. An Internet connection is not required.

1. Connect your computer or mobile device to the same LAN as the base

station.

If you are unable to connect to the same LAN using WiFi, use an Ethernet

cable to connect a computer to the same router or switch as the base

station.

2. Do one of the following:

• Windows-based computer. Open a folder and then click

Network or Network Places. Look for a FlexPowerBS-xxx

icon. It might appear in the other devices category.

• Mac, Linux, or mobile device. Open a web browser and enter

http://FlexPowerBS-xxx/ (replace xxx with the last 3 digits

of the base station serial number). The serial number is on the

base station label.

• IP address. Use your router’s admin web interface or a

network scan tool to look up the IP address for the base

station and then type the IP address into your browser

address bar.

3. Enter the password.

The default password is password.

4. When prompted, create a new password.

You are prompted to select 60 hz or 50 hz for the ﬂicker setting.

5. Either accept the 60 hz default setting, or select 50 hz.

The home page displays all cameras that are paired to the base station.

To change the camera names, use the Camera Settings menu for each

camera.

To refresh the camera image, tap or click the Snapshot button for each

camera. This is useful when mounting and positioning the camera.

For optimal performance, we recommend that you set up motion detection

sensitivity and a motion detection schedule, as described in the Wire-Free IP

Camera Base Station User Manual.

Installation on a Flat Surface

You can mount the base station on a ceiling or wall, or install it on a ﬂat

surface. For optimal antenna performance, we recommend mounting the

base station on a ceiling or installing it on a ﬂat surface. For information

about how to mount the base station, see the other side of this document.

For installation on ﬂat surface, attach the four round rubber feet to the

locations marked by the gray circles on the bottom of the base station.

The FlexPower Base Station accepts WiFi streaming video data from

FlexPower ONVIF Wire-Free IP Cameras and delivers the video data to ONVIF-

compliant VMS platforms such as Milestone. Each base station supports WiFi

streaming from up to four cameras.

Quick Start Guide

November 2018

Technologies, Inc. Other trademarks are for reference purposes only.

Compliance

For regulatory compliance information including the EU Declaration of Conformity, visit

www.arlo.com/about/regulatory/.

Arlo Technologies, Inc.

2200 Faraday Ave. Suite 150

Carlsbad, CA 92008 USA

www.arlo.com

www.arlo.com/support

Arlo International, Ltd.

Floor 3, Building 3 University Technology Center

Curraheen Road, Cork, Ireland

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Netgear Arlo FlexPower Base Station VNB4000 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info