Bedienungsanleitung Netgear WG102-500 (Seite 1 von 2) (Englisch)

519681

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Installation Guide

NETGEAR ProSafe® 802.11g Wireless Access Point, WG102-

500, WGAP150

Start Here

Please refer to the Reference Manual for instructions about advanced configuration

options. The Reference Manual is available on the Netgear website.

Estimated Installation Time: 30 minutes.

Tip: Before mounting the WG102-500 in a high location, first set up and test the

WG102-500 to verify wireless network connectivity.

Note: The Wireless Access Point does not include an external antenna. You must

connect a suitable antenna to the Wireless Access Point before powering on the

access point.

First, Set Up the Wireless Access Point

1. Connect the WG102-500 to the Computer

a. Unpack the box and verify the contents.

b. Prepare a computer with an

Ethernet adapter. If this computer

is already part of your network,

record its TCP/IP configuration

settings. Configure the computer

with a static IP address of

192.168.0.210 and

255.255.255.0 as the subnet

mask.

c. Connect an Ethernet cable from

the WG102-500 to the computer

(point A in the illustration).

d. Securely insert the other end of the

cable into the WG102-500

Ethernet port (point B in the illustration).

e. Turn on your computer, connect the power adapter to the WG102-500 and

verify the following:

Power: The power light on the WG102-500 should be steady

green. If the power light is not lit, check the connections, and check

if the power outlet is controlled by a wall switch that is turned off.

Status: The status light on the WG102-500 should be blinking red

while the WG102-500 starts up. When the startup process is

complete, the status light should be steady green to indicate that the

WG102-500 is ready.

LAN: The LAN light on the WG102-500 should be blinking green. If

it is not, make sure that the Ethernet cable is securely attached at

both ends.

Wi-Fi: The Wi-Fi light on the WG102-500 should be blinking green

when the wireless LAN (WLAN) is ready.

2. Configure LAN and Wireless Access

a. Configure the WG102-500 Ethernet port for LAN access.

• Connect to the WG102-500 by opening your browser and

entering http://192.168.0.229 in the address field.

• When prompted, enter admin for the user name and

password for the password, both in lower case letters.

• Click the Basic Settings link and configure the IP Settings for your

network.

b. Configure the wireless interface for wireless access. See the Reference

Manual for full instructions.

c. Test wireless connectivity using a computer with a wireless adapter

configured according to the wireless settings you just set in the WG102-500

to establish a wireless connection to the WG102-500.

d. Now that you have finished the setup steps, you are ready to deploy the

WG102-500 in your network. If needed, you can now reconfigure the

computer you used in step 1 back to its original TCP/IP settings.

Then, Deploy the Wireless Access Point

1. Disconnect the WG102-500 and position it where you will deploy it. The best

location is elevated, such as wall mounted or on the top of a cubicle, at the

center of your wireless coverage area, and within line of sight of all the mobile

devices.

2. Position the antenna. Vertical positioning provides best side-to-side coverage.

Horizontal positioning provides best top-to-bottom coverage.

3. Connect an Ethernet cable from your WG102-500 to a LAN port on your router,

switch, or hub.

4. Connect the power adapter to the wireless access point and plug the power

adapter in to a power outlet. The PWR and LAN lights should light up.

Tip: The WG102-500 supports Power Over Ethernet (PoE). If you have a switch that

provides PoE, you will not need to use the power adapter to power the

WG102-500. This can be especially convenient when the WG102-500 is

installed in a high location far away from a power outlet.

Now, Verify Wireless Connectivity

Using a computer with an 802.11g or 802.11b wireless adapter, verify connectivity

by using a browser such as Internet Explorer or Mozilla Firefox to connect to the

Internet, or check for file and printer access on your network. In order to connect to

the Internet, your network must include a router that provides Internet access.

Note: If you cannot connect, see to Troubleshooting Tips in this guide or the

Reference Manual for the ProSafe® 802.11g Wireless Access Point.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Netgear WG102-500 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Netgear WG102-500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info