Bedienungsanleitung Netgear WGL102 (Seite 1 von 2) (Englisch)

519680

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

)NSTALLATION'UIDE

ProSafe Light Wireless Access Point, WAGL102 or WGL102

Start Here

This guide describes installation for the WAGL102 ProSafe™ 802.11a/g Dual Band Light

Wireless Access Point or WGL102 Prosafe 802.11g Light Wireless Access Point.

Note: The WAGL102 or WGL102 Light Wireless Access Points work only in conjunction

with the WFS709TP ProSafe Smart Wireless Switch. In order to complete access point

installation, the WFS709TP should be already configured and available on your network.

For instructions on advanced configuration options for access points, please refer to the

WFS709TP ProSafe Smart Wireless Switch Software Administration Manual, which can

be downloaded from http://www.netgear.com/support.

Estimated Completion Time: 20 minutes.

Installing the Access Point

1. Unpack the box and verify the contents, as follows:

• WAGL102 ProSafe 802.11a/g Dual Band Light Wireless Access Point or

WGL102 Prosafe 802.11g Light Wireless Access Point

• Antenna:

- WAGL102—one 2.4 GHz antenna and one 5 GHz antenna

- WGL102—one 2.4 GHz antenna

• Wall mounting screws

• Straight through Category 5 Ethernet cable

• Power adapter and cord (12 V dc, 1.2 A)

• ProSafe Light Wireless Access Point, WAGL102 or WGL102 Installation Guide

(this document)

• Support Registration card

Note: Contact your reseller or customer support in your area if there are any missing or

damaged parts. You can refer to the Support Information Card for the telephone

number of customer support in your area. You should keep the Support Information

card, along with the original packing materials, and use the packing materials to

repack the WAGL102 or WGL102 if you need to return it for repair.

2. Connect the access points directly to the WFS709TP ProSafe Smart Wireless Switch

to configure them and to download firmware (for full instructions, see the

documentation for the WFS709TP ProSafe Smart Wireless Switch).

3. Mount or place the access point where you intend to deploy it.

4. Power the access point by one of these methods:

• Power adapter—connect to a power source using the supplied power adapter.

• PoE (power over Ethernet)—connect an Ethernet cable between the access

point’s 65 FE Port and:

- A network port on a WFS709TP ProSafe Smart Wireless Switch, or

- A network mid-span device that supports a 802.3af compliant port.

5. Orient the antenna (for best performance, a vertical position is recommended).

6. Verify successful installation by observing the LED status:

7. Complete your installation by defining the operational behavior for each access point

in your network.

Troubleshooting Tips

Here are some tips for correcting simple problems you may have.

No lights are lit on the access point.

• Make sure the power is connected to the access point.

LED Color(s) Activity Action

ENET (10/100 Mbps) Green Off No link

Green on 10/100Mbps link negotiated

Green flashing 10/100Mbps data activity

WLAN LEDs Green Off Wireless radio disabled

Green on Wireless radio AP mode enabled

Green flashing Wireless radio AM mode enabled

• Make sure the Ethernet cable connectors (if used) are securely plugged in at the

access point and the network device (hub, switch, or router).

• Make sure the connected device is turned on.

The WLAN lights are not lit.

• Disconnect the adapter from its power source and then plug it in again. Contact

NETGEAR if the Wireless LAN lights remain off.

I cannot configure the access point from the WFS709TP ProSafe

Smart Wireless Switch.

• Check that the WAGL102 or WGL102 is properly installed, the LAN connections are

OK, and that the LAN port LED is green. Check the operational status of the

WFS709TP ProSafe Smart Wireless Switch.

Specifications

Parameter WAGL102 ProSafe 802.11a/g Dual Band Light Wireless Access Point

or WGL102 Prosafe 802.11g Light Wireless Access Point

Maximum Clients Limited by the amount of wireless network traffic generated by each node;

typically 15 to 20 nodes.

Status LEDs Power/Ethernet LAN/Wireless LAN/Test

Power Adapter 12V DC, 1 A

Environmental

Specifications

Operating temperature: 0 to 50° C

Operating humidity: 5-95%, non-condensing

Antenna • WAGL102: One (1) external 5dBi 2.4 GHz detachable antenna and one (1)

external 5 dBi 5GHz detachable antenna

• WGL102: One (1) external 5 dBi 2.4 GHz detachable antenna

Wireless LAN

network

standards

IEEE 802.11a, IEEE 802.11b and IEEE 802.11g

Radio technology • 802.11b: 1 and 2 Mbps, Direct Sequence Spread Spectrum (DSSS)

• 802.11b: 5.5 and 11 Mbps, Complementary Code Keying (CCK)

• 802.11g: All rates, Orthogonal Frequency Division Multiplexing (OFDM)

Radio modulation

type

• 802.11a - BPSK, QPSK,16-QAM, 64-QAM

• 802.11b - CCK, BPSK, QPSK

• 802.11g - CCK, BPSK, QPSK,16-QAM, 64-QAM

Media Access

Control

CSMA/CA with ACK

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Netgear WGL102 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info