718524
15
Zoom out
Zoom in
Vorherige Seite
1/18
Nächste Seite
EN
If the screen displays an error code “Ex”, please refer to the table below.
E5 error code
- Reset thermal cutout
(1) Cut off power of pump
(2) Insert the stopper caps onto the inlet and outlet on the pool inner wall
(3) Disassemble pump, turn over the pump.
(4) Locate the small hole marked “RESET” on the bottom of pump. Then, inset a small stick (It should be less than Ø0.9cm,
length is longer than 10cm) into the hole, press down, you can hear “ping”, the reset is successful.
(5) Then, connect pump with pool again. Take off the stopper on the inner pool and repeat the previous outlined steps to use
your SPA.
6.2. Error code
Code Situation Problem Causes Solutions
E1
Not heating Not
heating properly.
Wrong temperature
control sensor.
Temperature control sensor short
circuit or open circuit.
Contact NetSpa service center.
E2
Not heating
properly.
Wrong temperature
control sensor.
Temperature control sensor short
circuit or open circuit.
Contact NetSpa service center.
E3
Not heating
properly.
High water tempera-
ture indicator.
The lled water is over 45°C
(113°F).
·Cut off the power, make sure the pool
water is between 2°C~44°C (36°F~111°F)
·If this does not solve the problem, contact
NetSpa service center.
E4
All functions do
not work, buzzing
warn.
Low water tempera-
ture indicator.
The pool water is lower than 2°C
(36°F).
·Cut off the power, make sure the pool
water is between 2°C~44°C (36°F~111°F)
·If this does not solve the problem, contact
NetSpa service center.
E5
All functions do
not work, buzzing
warn.
High water tempera-
ture indicator.
The lled water is over 50°C
(122°F).
·Cut off the power, turn to qualied
electrician to reset the thermal cutout
described in next paragraph. If this does
not solve the problem, contact NetSpa
service center.
E6
Not heating and
ltering properly.
Buzzing warns.
Water pressure is
not big enough to
activate heating.
·Inlet or outlet on inner wall are
blocked.
·Filter cartridge is too dirty.
·Pool water does not reach mini-
mum water level.
·Do not release air from pump
Pump is wrong”
·Clean inlet and outlet
·Clean or replace lter cartridge
·Add water to reach water level
·Do air release as outlined again
·If this does not solve the problem, contact
NetSpa service center.
E7
All functions do
not work, buzzing
warn.
Dry-run heater.
Heating at no water situation,
system shut down automatically
Contact NetSpa service center.
15
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Netspa Vita Premium wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Netspa Vita Premium

Netspa Vita Premium Bedienungsanleitung und Installationsanweisung - Deutsch - 18 seiten

Netspa Vita Premium Bedienungsanleitung und Installationsanweisung - Französisch - 18 seiten

Netspa Vita Premium Bedienungsanleitung und Installationsanweisung - Italienisch - 18 seiten

Netspa Vita Premium Bedienungsanleitung und Installationsanweisung - Spanisch - 18 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info