776299
97
Zoom out
Zoom in
Vorherige Seite
1/99
Nächste Seite
SECTION VI THEORY OF OPERATION
Utrecht
- 96 - Ref 001
5. CONNECTING AND DISCONNECTING MODEMS
When the modems are connected and suitably set at the instrument and the PC, just click
the “Make modem connection” button in Power Link toolbar or select “Make modem
connection” in Modem menu. It takes a few seconds (up to 30 s) to establish
communication link. The instrument operates as it is connected directly to the PC via
RS232 interface. It means that all interface functions are active, e.g.: receive / transmit
instrument settings, data download, manipulating of the recording function, clear memory.
To disconnect just click on “Hang-up modem connection“ button on Power Link toolbar
or select “Hang-up modem connection” in Modem menu.
6. SMS MESSAGES
The instrument has possibility to send an SMS message to the mobile phone when GSM
modem communication is enabled. Messages are intended to inform the operator about
some events regarding the instrument.
The following events can be sent as SMS messages:
- Less than 50% of recording memory is free.
- Less than 20% of recording memory is free.
- Recording memory is full.
- WAVEFORM, FAST LOGGING, TRANSIENT, EN50160 or PERIODICS recording is
finished.
For SMS messaging prepare the following configuration:
ENABLE PASSW.
GSM/SMS PARAM. => ENABLED >> DISABLE
DATE/TIME CPIN :
LANGUAGE DEST: XXXXXXXXXXXX
SYSTEM REINIT. USERID: XXXXXXXXXX
CLR.REC.MEM. SEND TEST MESSAGE
- Enter Destination phone number “DEST:” (phone number of the mobile phone that will
receive SMS messages from the instrument) using cursor keys.
- Enter user ID “USER ID”: (optional instrument identification string) using cursor keys
as described in chapter 3.4.
- Provide PIN card of modem terminal with the number of your local.
- It can be done with “SEND TEST MESSAGE” command in GSM/SMS PARAMETERS
menu of the instrument.
Press Enter to confirm settings or ESC to discard them.
Note:
- SMS message cannot be sent if modem communication is established.
If you do not want the instrument to send SMS, disable GSM/SMS PARAM. and set baud
rate to 9600
97

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Nieaf-Smitt PQA 6600 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info