Bedienungsanleitung Nikon Coolwalker MSV-01 (Seite 74 von 80) (Englisch)

570921

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Technical Notes—Troubleshooting

Troubleshooting

If your MSV-01 fails to function as expected, check the list of common problems below before con-

sulting your retailer or Nikon representative.

Refer to the page numbers listed in the right-most column for information on solving the problems listed here.

If You Hear an Unusual Noise from the Main Unit

If you hear any kind of unusual rattling or grinding sound coming from the internal HDD during

operation, it is possible that its operating life is coming to end.

Create a backup of the data stored on the internal hard disk of the device using an alternative

recording medium, and contact your retailer or Nikon representative.

Electronically-controlled devices

In extremely rare instances, the MSV-01 may fall in unoperatable state (freeze during opera-

tion). Press the power switch to turn the MSV-01 off.

• If the MSV-01 does not go off even when you press the power switch, you may

need to reset the MSV-01.

To reset the unit, simultaneously press and hold down the power switch and right function

button for several seconds.

* Note that resetting the unit as described above may result in the loss or corruption of any data

not yet recorded to the memory card or hard disk at the time the problem occurred.

• If the problem persists, perform the following steps:

1 Disconnect the AC adapter from the MSV-01 (if connected).

2 Remove and re-attach the battery pack.

When the MSV-01 is used on battery power for an extended period, the battery pack

may become hot. Be careful to avoid burns.

3 Turn the MSV-01 on again.

In the event of continued malfunction, contact your retailer or Nikon representative. Note

that disconnecting the power source as described above may result in the loss of any data

not yet recorded to the memory card or hard disk at the time the problem occurred.

Problem Possible Cause

LCD monitor is

blank

• The MSV-01 is off.

• Battery pack is not correctly inserted or battery contacts

are covered with insulating tape.

• Battery is exhausted.

• AC adapter is not correctly connected.

• A/V cable is connected to the MSV-01.

MSV-01 turns off

without warning

• MSV-01 is turned off with Auto power off function.

• Battery is low.

• Battery is cold.

Monitor is hard to

read

• Ambient lighting is too bright: move to a darker location.

• Monitor brightness needs adjustment.

• Monitor is dirty: clean monitor.

–

Computer does not

recognize MSV-01

• MSV-01 is off.

• AC adapter is not correctly connected.

• Battery is low.

• USB cable is not correctly connected.

• COOLWALKER MSV-01 USB driver is not installed on computer

(Windows 98 SE only): install software from supplied CD.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nikon Coolwalker MSV-01 Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nikon Coolwalker MSV-01

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info