Bedienungsanleitung Nilfisk-ALTO SCRUBTEC R 466 (Seite 80 von 124) (Deutsch, Englisch, Holländisch, Französisch)

609460

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH USER MANUAL

18 SCRUBTEC R 466 - R 471 - R 471C - BOOST

R4 9098960000(1)2011-04 A

MACHINE START AND STOP

Starting the machine

Prepare the machine as shown in the previous paragraph.1.

Turn the ignition key (58) to “I” without pressing the drive pedal (4). Check if the battery green warning light (62) turns on.2.

If the yellow or red warning light turns on, turn the ignition key (58) back to “0” and charge the batteries (see the procedure in

Maintenance chapter).

Drive the machine to the working place, by starting it with the hands on the steering wheel and by pressing the pedal (4).3.

Adjust the speed with the switches (69) according to the necessities or the work to be performed.

The reverse speed is selected with the switch (51, LED 52 on).4.

To go back to forward speed press again the switch (51, LED 52 off).5.

NOTE

The driver’s seat (17) is equipped with a safety sensor which allows the machine to be moved with the pedal (4) only

when the operator is on the driver’s seat.

NOTE

The machine is equipped with an anti-skid safety system (LED (72) ﬂ ashing) that reduces the speed when turning and

when the machine tilts laterally, irrespectively of the pressure on the pedal.

In this case, the reduction of speed is not a malfunction but a characteristic that improves the machine stability and

safety in every condition.

Lower the brush/pad-holder deck and the squeegee by pressing the pedal (63).6.

Press the solution ﬂ ow control switches (59 and 60) according to the type of cleaning to be performed.7.

Start scrubbing, by starting it with the hands on the steering wheel (1) and by pressing the pedal (4).8.

NOTE

The machine is equipped with a safety system that turns on the brushes and vacuum system only when the machine is

moving.

Stopping the machine

Release the pedal (4).9.

It is not necessary to lock the machine during stopping or parking, because the electromagnetic brake on the wheel turns on 10.

automatically when the drive pedal is not pressed.

Lift the brush/pad-holder deck and the squeegee by pressing the pedal (63).11.

MACHINE OPERATION (SCRUBBING/DRYING)

Start the machine as shown in the previous paragraph.1.

If necessary, adjust the solution quantity by pressing the switches (59 and 60).2.

If necessary, to reduce the noise, turn on the mute function by pressing the switch (55).3.

NOTE

It is suggested to use the mute function only on smooth ﬂ oors without joints.

NOTE

For correct scrubbing/drying of ﬂ oors at the sides of the walls, Nilﬁ sk Alto suggests to go near the walls with the right side

of the machine as shown in ﬁ gure 4.

Figure 4

P100438

9098960000(1)2011-04 A.indb 189098960000(1)2011-04 A.indb 18 07/04/2011 15:59:2107/04/2011 15:59:21

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk-ALTO SCRUBTEC R 466 Seite 80

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info