609460
83
Zoom out
Zoom in
Vorherige Seite
1/124
Nächste Seite
USER MANUAL
ENGLISH
9098960000(1)2011-04 A SCRUBTEC R 466 - R 471 - R 471C - BOOST
®
R4 21
Cylindrical brush debris container emptying (only for cylindrical brush deck)
Stop the machine.14.
Lower the cylindrical brush deck and remove the debris container (F, Fig. 2).15.
Empty and wash the debris container (F), and then install it on the relevant stand.16.
AFTER USING THE MACHINE
After working, before leaving the machine:
Remove the brushes/pad-holders as shown in the relevant paragraph.1.
Empty the tanks (19 and 22) as shown in the previous paragraph.2.
Remove the squeegee (30) and clean it with hot water.3.
Perform the daily maintenance procedures (see the Maintenance chapter).4.
Store the machine in a clean and dry place, with the brushes/pad-holders and the squeegee lifted or removed.5.
PUSHING/TOWING THE MACHINE
To push/tow the machine easily when the drive system cannot be used (for example in case of missing batteries, discharged
batteries, etc.), disengage the electromagnetic brake by pulling the lever (7) and locking it with a spacer.
When the operation is over, remove the spacer under the lever (7) to activate the electromagnetic brake again.
WARNING!
If the lever (7) is not disengaged after pushing/towing the machine, the electromagnetic brake is disengaged.
WARNING!
Do not start the machine when the electromagnetic brake is disengaged.
For safety reasons, it is recommended to disengage the electromagnetic brake only for the time necessary to
manually move the machine.
MACHINE LONG INACTIVITY
If the machine is not going to be used for more than 30 days, proceed as follows:1.
Perform the procedures shown in After Machine Use paragraph.2.
Before disconnecting the battery red connector (9) perform the following procedures:3.
Open the cover (20) and the ller neck (23), then check that the tanks (19 and 22) are empty, otherwise empty them.
Keep the recovery tank assembly (19) lifted by using the stand (25).
FIRST PERIOD OF USE
After the rst 8 hours, check the machine fastening and connecting parts for proper tightening. Check the visible parts for integrity
and leakage.
9098960000(1)2011-04 A.indb 219098960000(1)2011-04 A.indb 21 07/04/2011 15:59:2207/04/2011 15:59:22
83

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Nilfisk-ALTO SCRUBTEC R 466 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info