Bedienungsanleitung Nilfisk C 110.4 X-TRA (Seite 11 von 17) (Englisch)

505725

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

11Original Instructions

In case problems other than the above occur, please contact your local Nilﬁ sk distributor. Local Nilﬁ sk distri-

butors are listed on the back cover of this instruction.

Customer Service at Penrith – 01768 868995

8 Warranty Conditions

Nilﬁ sk guarantees high pressure washers for domestic use for 2 years. If your high pressure washer or ac-

ces so ries are handed in for repair, a copy of the receipt must be enclosed.

Guarantee repairs are being made on the following con dit ions:

• that defects are attributable to ﬂ aws or defects in materials or workmanship. (wear and tear

as well as misuse are not covered by the gu a ran tee).

• that the directions of this instruction manual have been thoroughly observed.

• that repair has not been carried out or attempted by other than Nilﬁ sk-trained service staff.

• that only original accessories have been applied.

• that the product has not been exposed to abuse such as knocks, bumps or frost.

• that only water without any impurities has been used.

• that the high pressure washer has not been used for rental nor used com mer cial ly in any

other way.

Repairs under this guarantee include replacement of defective parts, exclusive of packing and postage/car-

riage. Besides, we refer to your national law of sale.

The machine should be forwarded to one of the service centres of the Nilﬁ sk organisation with description/

spe ci ﬁ ca ti on of the fault.

Repairs not covered by the guarantee conditions will be invoiced. (I.e. malfunctions due to Causes men ti-

o ned in section Troubleshooting Chart of the instruction manual).

Symptom Cause Recommended action

Machine stops Fuse has blown

Incorrect mains voltage

Thermal sensor activated

Nozzle partially blocked

Replace fuse. Switch off other machines.

Check that the mains voltage corresponds

to speciﬁ cation on the model tag.

Leave the washer for 5 minutes to cool

down.

Clean the nozzle (see section 6.2)

Fuse blows Fuse too small Change to an installation higher than the

amp. consumption of the machine.

You may try without the extension cable.

Machine pulsating Air in inlet hose/pump

Inadequate supply of mains

water

Nozzle partially blocke

Water ﬁ lter blocked

Hose kinked

Allow machine to run with open trigger until

regular working pressure resumes.

Check that the water supply corresponds to

speciﬁ cations required (see model tag)

NB! Avoid using long, thin hoses (min. 1/2")

Clean the nozzle (see section 6.2)

Clean the ﬁ lter (see section 6.1)

Straighten out hose.

Machine often starts

and stops by itself

Pump/spray handle is leaking Contact your nearest Nilﬁ sk Service Centre.

Machine starts, but no

water comes out

Pump/hoses or accessory

frozen

No water supply

Water ﬁ lter blocked

Nozzle blocked

Wait for pump/hoses or accessory to thaw.

Connect inlet water.

Clean the ﬁ lter (see section 6.1)

Clean the nozzle (see section 6.2)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk C 110.4 X-TRA Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nilfisk C 110.4 X-TRA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info