Bedienungsanleitung Nilfisk family (Seite 25 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

315566

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Fault finding

• the motor will not start

– a fuse may have blown and needs replacing.

– the cable may be defective and needs checking.

• the suction power is reduced

– the dust bag may be full and needs replacing.

See point 3.

– the dust filters may be clogged and need replacing.

See point 3-4-7.

– the hose, tube or nozzle may be blocked and needs to be

cleared.

• the vacuum cleaner stops

– the thermal cut-out has switched off the motor as a result of an

obstruction of the hose, tube or nozzle.

Remove the cause of the obstruction.

Maintenance

Always keep the cleaner in a dry place. The cleaner is designed for

continuous heavy work. Depending on the number of running hours

- the dust filters should be renewed.

Keep the container clean with a dry cloth, and a small amount of

spray polish.

For details of after sales service contact Nilfisk-Advance directly.

4. Changing the HEPA filter

Replacing the HEPA exhaust filter. In models with HEPA filter

placed under the handle cover:

1. Push the button inside the handle upwards and twist the handle

counter-clockwise and remove it.

2. Remove the HEPA filter.

3. Replace with the new HEPA filter and position it as shown.

4. Locate the handle into position and lock it by turning it

clockwise until it snaps.

All models

Damage resulting from the use of filters other than original Nilfisk

filters is not covered by the guarantee.

5. Suction power regulation

1. The suction power of the nozzle can be regulated by the slide

valve on the curved tube.

Suction is most powerful when the valve is pushed forward to

close the inlet.

2. For cleaning of e.g. Ioose covers and curtains, the suction power

can be reduced by sliding the valve backwards.

Models with two speed regulation

Suction is variable by changing the speed. See point 1.

6. Parking of the tube with nozzle

During and after cleaning you can park the hose with tube and

nozzle.

1. Press the parking clip on the nozzle inside the groove on the

back-side of the container

7. Main filter cleaning

The main filter can be cleaned with a dust bag in place, when the

suction efficiency is falling.

1. Open the container by pushing the knob on the lock.

2. Press the plastic flap inside the groove for the lock to release the

upper container from the main filter and remove the upper

container.

3. Remove the main filter from the bottom housing.

4. Replace the upper housing on the bottom housing with a dust

bag in place.

5. Start the vacuum cleaner.

6. Clean the filter material with the vacuum cleaner

7. Replace the cleaned main filter

8. Replace the upper container on top of the main filter

9. Lock the plastic flap on the upper container on the main filter

frame.

10. Close the lock.

Thermal cut-out protection

The vacuum cleaner is equipped with a thermal cut-out to protect

the motor and other vital machine parts from overheating. Should

the machine cut out, you will have to wait at least 5-10 minutes for

it to automatically reset. While you are waiting, switch the machine

off and unplug it, then check the hose, dust bag and filters to be sure

that nothing is blocking the flow of air through the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk family Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info