Bedienungsanleitung Nissin MG8000 Extreme - Nikon (Seite 7 von 11) (Englisch)

667851

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

23 24

The mode to be set on the camera:

MG8000 provides two possibilities of off camera wireless remote flash system.

This page explains Wireless Remote flash system. (The other system,

universal slave flash system, is prepared at M and Av. mode - Ref. page 16/ 20)

The flash unit placed on the camera, connected by TTL off-camera flash cord is

called “Master flash”. The master flash to be set is one unit only.

The flash unit placed off the camera is called “Remote Flash”. Multiple number

of flashes can be set and controlled in 3 different groups (A, B and C group). 4

channels are prepared for signal transmission between the Master flash and

the Remote flash.

Wireless Remote Flash Mode

Available combination of flash models and cameras

NOTE

The shutter speed to be set on the camera is calculated in the following formula.

Caution

When using an external power pack, you may take continuous frames of

multi-exposure pictures. To enjoy the extreme feature without overheating

problem, it is suggested to take an interval of 3 seconds between shots

and maybe longer time after 200 shots.

Flash source may be heated up and may cause serious damage to the

flash unit if it is overly operated.

Please note that the basic operation is however controlled by the main

batteries(battery magazine) in the flash unit and when the main batteries

are exhausted, flash control system does not work. Replace the batteries

when recycle time becomes longer than 20 seconds by main batteries only.

- ref. External Power Pack (page 34)

Number of flashes ÷ Frequency ＝ Shutter Speed

Guide Table for the number of flashes

Example : To get 20 flashes at 10Hz 20÷10＝2

The shutter speed to be set on the camera is 2 seconds or longer.

Shutter for bulb setting is also available.

1/8

1/16

1/32

1/64

1/128

Wireless TTL Flash Pairing Chart

1 2 3 4 5 6-7 8-9 10 11 12-14 15-19 20-50 51-90

There is no limit of the number of slave flashes to set at one time.

It is however recommended to set maximum 3 pcs in one group, as it may

cause interference between flashes depending on the photographic conditions.

At Remote flash mode, MG8000 is set automatically for manual zoom setting and

its reflector position is set for 24mm to cover the wider range of illumination. It is

possible to set the desired flash coverage angle manually by select button

Use a flash stand to set the slave flash. The stand provides the flash shoe and

can stay either on the flat surface, or be placed on the tripod or light stand by

the screw provided at the bottom.

When setting MG8000 to slave flash, it is recommended to cancel the auto-off

setting or set it to 60 minutes at the Custom Settings - Ref. page 30.

Refer your flash instruction manual for this function, which may differ according

to the flash model.

Remote flash (Slave flash)

1.The slave flash does not shoot its light directly into the camera lens.

2.The wireless flash sensor of the slave flash is not blocked.

3.The slave flash is usually not placed behind the master flash.

4.In the daylight synchronization, the sensor of slave flash could be

saturated by sunlight and its response will be extremely reduced. In this

case, the wireless TTL function may not result in success. Making a shade

to cover the sensor of slave flash is one of the ideas to help the situation.

Where is the Slave flash sensor?

Slave flash sensor is provided behind the front panel of MG8000 at the

name of Nissin DIGITAL. The sensor’s sensing angle to respond to the

incoming light is about 100 degree.

Place the slave flash in consideration to;

Power

(Full Auto), (Program), (Shutter priority),

(Aperture priority), (Manual),

Master flash

Group Setting

Remote flash

Nissin Di866

Nissin MG8000

Nissin Di866

Nissin Di866 Mark II

Nissin Di622 Mark II

Nikon SB800

Nikon SB900

Nikon SB910

Nikon SB600

Nikon SB-R200

Nikon SB700 (A/B/C)

A, B, C

D700

D300

D200

D90

D80

D300s

A, B

Built-in Camera flash

D70s D70

Built-in Camera flash

D7000

D800

Nissin Di866 Mark II

Nikon SB800

Nikon SB900

Nikon SU-800

(commander)

A, B

Nikon SB700

Setting the Master flash

In the main page

Select Wireless mode.

In the Wireless page

Select Master mode.

In the Master page

Navigate the cursor and adjust the value according to the

instruction at the bottom bar.

Cursor Navigation

Value Adjust

Channel Select

Select Channel: Ch1, Ch2, Ch3 & Ch4

Zoom Select

Select Zoom Mode: Auto, 24mm, 28mm, 35mm, 50mm,

70mm, 85mm, 105mm

Group Setting

Group

M = Master Flash

A = Group A

B = Group B

C = Group C

Flash Mode

TTL = TTL Mode

M = Manual Mode

--- = Flash off

Value Adjustment

Ev compensation at TTL mode

(-3.0Ev to +3.0Ev)

Power Ratio at M mode

(1/1, 1/2, 1/4, 1/8, 1/16,

1/32, 1/64, 1/128)

The modes available on the Master flash are TTL and M mode.

The master flash sets the signal transmission channel, flash reflector zooming

position, flash mode of the master flash itself and flash mode and value

adjustment of the Remote flash at A, B and C respectively.

Channel 1 Group A only

Nissin MG8000

Nissin MG8000 Extreme - Nikon Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nissin MG8000 Extreme - Nikon

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info