Bedienungsanleitung Nivona CafeRomatica 845 (Seite 6 von 29) (Englisch)

488213

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

as the lter softens the water. The machine’s default factory setting

is “Insert lter? No”.

! Turn the Rotary control knob to select “Insert lter? Yes”, so that

the machine knows that the lter is being inserted.

! Press the Rotary control knob. The message, “Insert lter”, will

appear on the display screen.

! Empty the water reservoir (Image 1/F and 2) and carefully screw

the lter into the holder provided in the water reservoir using the

assembly tool on the end of the measuring spoon (Image 4).

Caution: Be careful not to turn too far or to cause it to snap off.

! Fill the water reservoir with fresh water and put it back into the

machine.

! Place a receptacle with at least 0.5l capacity under the spout and

slightly to the left (Image 1/E) and press the Rotary control knob.

The system will now be rinsed. The message, “Rinsing Filter”, will

appear on the display screen.

! Wait until water stops coming out of the spout.

The message, “Please rinse”, will appear on the display screen.

! Press the Rotary control knob.

The machine will be rinsed and will then be ready for use.

Please note: If you operate the machine with the lter and have set the

system to “Filter inserted? Yes”, you cannot set water hardness. The

machine is set to water hardness level 1 by default. This means that you

have to descale your machine less often – but you must still descale

it when necessary. ALWAYS TAKE THE FILTER OUT before descaling!

The lter loses its efciency after processing about 50 l of water. (To

change the lter, see 3.1.1).

Caution: Even if the display screen does not show the message, “Replace

lter”, and even if the machine is only used occasionally, the lter must

be changed at least every two months (see 3.1.1.).

Operating the machine without the lter

If you wish to operate the machine without the lter, you must reset

the lter setting to “Filter inserted? No”. This is important because

the machine needs to be descaled more often without a lter, de-

pending on water hardness (the machine’s default factory setting is

“Filter inserted? No”!).

! Turn the Rotary control knob to select “Filter inserted? No”.

! Press the Rotary control knob to conrm your selection.

The water hardness setting will now appear on the display screen.

Please note: It is possible that the machine’s pipe system will still be

empty when it is set up. This will be indicated when the machine is

turned on using the on/off button, as the message, “Fill up pipe system”,

will appear on the display screen.

! Place a receptacle with at least 0.5l capacity with its centre under

the spout.

! Press the Rotary control knob.

The system will now be lled. Water may come out of the spout

(Image 1/E ). After the system has heated up, the message, “Please

rinse”, will appear on the display screen.

! Press the Rotary control knob.

The system will now be lled with water.

! Setting the water hardness level

Depending on the level of water hardness in your area, the machine

will have to be descaled sooner or later. In order for the system to be

able to indicate when descaling is required, you must set the correct

water hardness level before using the machine for the rst time.

If you use the machine with a lter and set the appropriate lter set-

ting (see 3.1 below), water hardness will be set to level 1 by default.

The basic factory setting for water hardness is LEVEL 3.

Firstly, test the quality of your water with the enclosed test strip:

! Dip the test strip in the water and gently shake it off.

! After about a minute, you will be able to read the test result by

counting the number of red dots on the test strip.

! The settings for the different water hardness levels are as follows:

Test strip / Degree of hardness = display

1 red dot / 1–7° = (HARDNESS) LEVEL 1

2 red dots / 8–14° = (HARDNESS) LEVEL 2

3 red dots / 15–21 ° = (HARDNESS) LEVEL 3

4 red dots / >21 ° = (HARDNESS) LEVEL 4



2. Set up 2. Set up

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nivona CafeRomatica 845 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nivona CafeRomatica 845

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info