£ Press the coffee button (g. 1/D).
The appliance will now start making coffee.
£ Shortly before the set amount of coffee is ready, turn the aroma/volume selector (g. 1/B) slowly
to the left until the appliance stops working.
Make a note of the aroma/volume selector’s position for the size of the coffee cup.
3.5 Making two cups of coffee
Once you’ve chosen coffee strength (see chapter 3.2) and water volume (see chapter 3.3),
£ place two cups beneath the spout (g. 8).
The spout is adjustable in height to match the size of the cups.
£ Press the coffee button twice in succession (g. 1/D).
The display will show symbol S5
.
The appliance will now start grinding, pre-brewing and brewing.
The process can be aborted any time by pressing the coffee button (g. 1/D) again.
When making two cups the grinder will automatically do two rounds.
Attention: When making your rst coffee, the grinder box is still empty. It can therefore happen that the
symbol S3 will ash after the rst grinding and the appliance will not make any coffee .
£ In this case simply press the coffee button again (g. 1/D).
Tip: In case there is not enough water or the bean container runs out during the two grinding cycles or
the trays need emptying, the respective symbols will show on the display. In that case the second cup
will not be brewed. Follow the display and press the coffee button (g. 1/D) again for the second cup.
3.6 Making ground coffee
£ Turn the aroma/volume selector (g. 1/B) to the water volume required for one cup.
£ Open the lid of coffee powder chute (g. 1/N). Symbol S4 blinkt.
£ Pour in one level measuring spoon of ground coffee and close the lid.
Symbol S4
is ashing.
£ Place one or two cups under the coffee spout (g. 7 or 8) and press the coffee button (g. 1/D)
once or twice respectively.
The appliance will now start pre-brewing and brewing – without grinding.
Tip: If you have opened the lid of coffee powder chute accidentally or did not press the coffee button
after having poured in the ground coffee, the appliance will automatically start rinsing for a minute
once the lid is closed. The appliance will then be operational again.
Attention: The coffee powder chute is not a storage container. Therefore never pour in more than one
portion of coffee and only use fresh or vacuum-packed coffee ground from coffee beans. Do not use
water-soluble instant coffee!
3.7 Making hot water (e.g. for tea)
£ Hold a cup under the steam/hot water jet /Spumatore (g. 1/L).
£ Turn the steam/hot water control (g. 1/C) clockwise.
£ Fill the cup with the required water and turn the knob back anti-clockwise to position 0.
Danger: Risk of scalding! Escaping water may spray! The steam/hot water jet /the Spumatore becomes
very hot when used. Let the steam/hot water jet /the Spumatore cool down for a few minutes before
touching it. Only touch the rubber parts.
Tip: You can draw hot water for about 2 minutes, after that the appliance will automatically shut down.
By turning the steam/hot water control (g. 1/C) backwards and forwards, you can re-start the process.
3.8 Using the steam function, e.g. for heating or frothing liquids
£ Press the steam/rinsing button (g 1/E).
Whilst heating up, 5 red bars will ash at the bottom of the display. As soon as symbol S12
shows, steam is ready.
£ Immerse the steam/hot water jet (g. 1/L) into the cup/container with the liquid (e.g. milk).
£ Turn the steam/hot water control (g. 1/C) clockwise.
Attention: A small amount of water will initially precede the steam.
£ Symbol S12
ashes during the steaming process.
£ Turning the knob (g. 1/C) anti-clockwise back to position 0 will end the process.
£ Press the steam/rinsing button (g. 1/E) once again.
The appliance is now back to coffee mode.
Tip: You can draw steam for about 2 minutes, after that the appliance will automatically shut down. By
turning the steam/hot water knob (g. 1/C) back and forth, you can re-start the process.
Attention: Dried milk residue on the steam/hot water jet is difcult to remove. Clean immediately after
it has cooled off!
Attention: From time to time (ideally each time the appliance will not be used for a while, at any rate in
regular intervals!) the steam/hot water jet needs to be completely dismantled and thoroughly cleaned
under running water.
4. Cleaning and maintenance
Attention: If your appliance needs cleaning or maintenance, the display will show the respective sym-
bol. Please always follow these instructions, otherwise your warranty will be void. Read chapters 4.1
to 4.5 for further information. Should you wish to maintain or clean your device without being asked to
do so, please also follow the instructions in chapters 4.1 to 4.5.
4.1 Changing the lter
The lter will be at after about 50 l of water have been drawn. The display shows symbol S6 .
You can still make coffee, but we recommend to always change the lter immediately.
Attention: The lter needs changing after a maximum of two months if the appliance is not in regular
use. The display will show no status signal. Use the dial (by the month) at the top of the lter to select
the date of change.
£ Switch the appliance on.
£ Press the aroma/volume selector (g. 1/B) for more than 3 seconds to go to the maintenance
menu.
Symbol S6
, S7 or S11 will show up.
£ Turn the aroma/volume selector (g. 1/B) clockwise and anti-clockwise until symbol S6
shows
in display.
£ Empty the water tank (g. 4) and unscrew the lter, using the integrated tool at the end of the
measuring spoon. Discard the lter.
£ Set the dial (by the month) at the top of the new lter to either the date when the lter was
installed or the lter needs replacing.
£ Screw in the lter into the dedicated slot in the water tank, using the integrated tool at the end
of the measuring spoon (g. 6).
£ Fill the tank with fresh water and insert it back in the appliance.
£ Place a sufciently large bowl (minimum contents 0.5 l) under the steam/hot water jet/ Spuma-
tore (g. 1/L).
£ Press the aroma/volume selector (g. 1/B).
14 15
3. Making coffee 3. Making coffee / 4. Cleaning and maintenance
