Bedienungsanleitung Nokta Makro Gold Finder 2000 (Seite 1 von 2) (Englisch)

801558

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Turning On/Off the Device

To turn on the device, press and hold the On/Off button until the

bar starts filling up. To turn off the device, press and hold the button

until the display light turns off.

Sensitivity

This is the depth setting of the device. It is also used to

eliminate the ambient electromagnetic signals from the

surrounding environment and noise signals transmitted

from ground.

Sensitivity setting consists of 8 levels and is pre-defined for each

mode. Each mode starts with its default sensitivity setting and it can

be manually modified when necessary.

Note : If the ground is highly mineralized causing the device to

overload, decrease the Sensitivity until the overload warning icon

disappears from the screen.

Pinpoint

Pinpoint is to find the center or the exact location of a detected target.

To perform pinpoint :

1- After a target is detected, move the search coil aside where there

is no target response and push the Pinpoint button .

2- Keep the button pressed down and bring the search coil closer to

the target slowly and parallel to the ground.

3- Signal sound becomes stronger and changes in pitch while getting

closer to the target center. In addition, the bar on screen will rise or

fall based on signal strength.

4- Mark the position which provides the loudest sound using a tool or

your foot.

5- Repeat the above procedure by changing your direction 90°.

Actions to be performed from a couple of different directions will

narrow the target area and provide you with the most exact details

of the target location.

Frequency Shift

It is used to eliminate the electromagnetic interference that the device

receives from another detector which operates in the same frequency range

nearby or from the surroundings. If too much noise is received when the

search coil is lifted in the air, this may be caused by the local electromagnetic

signals or excessive sensitivity settings.

To shift the frequency, press and hold the M button for 3 seconds while

the device is on. The frame around the search modes icon will start blinking.

Change the frequency using the sensitivity +/- buttons.

Note : If no button is pressed for 5 seconds, the screen will time out and the

device will revert back to the main screen.

Frequency shift will be reflected on the left side of the bar. The left side of the

bar will start filling up / falling each time you press the sensitivity +/-

buttons. Frequency shift consists of 10 steps and 5 is the central frequency.

IMPORTANT! At each power up, the frequency shift setting will start at the

central frequency of 5.

Search Modes

There are 2 search modes: All Metal and Discrimination. Press the M

button to select the mode.

All Metal Mode

In this mode, the device does not provide audio tone discrimination

and gives the same audio tone for all types of targets.

Discrimination Mode

In this mode, the device does NOT provide any audio tone for ferrous

metals and it provides a high tone for non-ferrous metals.

In both search modes:

When the device detects a ferrous metal, the left side of

the bar fills up in proportion to the strength of the target

signal.

When the device detects a non-ferrous metal, the right

side of the bar fills up in proportion to the strength of the

target signal.

1) On / Off Button

2) Search Mode Button

3) Search Modes

4) Pinpoint Button

5) Volume Buttons

6) Sensitivity Buttons

7) Signal Strength Bar

8) Warning Icons

9) Battery Icon

10) Wireless Connection Icon

Control Display

Illumination LEDs

It is the flashlight used for lighting the area you are scanning while detecting

at night or in dark locations. To activate the LEDs, while the detector is on,

press the pinpoint and volume minus (-) buttons at the same time. Repeat

the same to turn them off. LEDs do not operate when the device is off. It is

recommended to turn them on only when necessary since they consume

extra battery power.

Volume

Press the + or - button to adjust the volume.

QUICK GUIDE

4 56

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nokta Makro Gold Finder 2000 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nokta Makro Gold Finder 2000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info