Bedienungsanleitung Novamatic WA6780 (Seite 48 von 52) (Deutsch, Englisch)

709023

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Problems

Repairs, alterations or intervention on electronic equip-

ment should only be carried out by qualied specialists.

Inexpert repairs can cause considerable damage and risk

to the user.

Only original spare parts should be used for repairs.

Please nd below minor faults which you can rectify

yourself.

Error messages on the display

If the following error messages are displayed, the pro-

gramme can be restarted by pressing the start button

once the error has been rectied.

«CHILD LOCK ACTIVE»

X Hold the

Quick Wash

button down and press the start

button.

«PLEASE CLOSE DOOR»

X Push the door closed until the lock catches properly.

«PLEASE START AGAIN»

 If the door was closed subsequently, the Start button

must be pressed again.

 After a power failure you must press the Start button

«CHECK WATER SUPPLY»

X Turn on the tap and start again.

X Filter in water supply is blocked: Clean the lter, see

chapter «Cleaning and Maintenance/Cleaning the lter

in the water inlet».

X Interruption in water supply.

«CHECK DRAIN»

X Check whether the drainage hose is blocked.

X Foreign bodies block the drain pump: clean pump

according to chapter «Cleaning and Maintenance/Emer-

gency emptying».

X The water drain provided by the customer is blocked:

Carry out an emergency discharge according to chapter

«Cleaning and Maintenance» and clean the drain si-

phon (built-in siphon).

X The position of the drain hose is too high. The maxi-

mum

pumping height is 1m above ground.

«UNBALANCE NO SPINNING»

X Excessive imbalance. Laundry not spun.

X Press the start button and then the Quick Wash button

to end the wash programme.

X Open the door and redistribute the load.

X Repeat the spin cycle with the separate spin programme.

General information:

X Avoid loading the drum with one single heavy item.

Wash large and small laundry together.

«FOAM PROG. EXTEND»

X The washing machine has detected foam and taken

adequate measures. The spinning cycle of the laundry

could be completed.

 In future, please reduce the detergent quantity.

«FOAM, PROG. CANCEL»

X Due to extremely intensive foaming, the washing

machine could not complete the spinning cycle and the

wash programme had to be aborted.

X Repeat the wash programme without adding any

detergent.

X In future, please reduce the detergent quantity (if

re quired use washing powder instead of liquid detergent).

«WATER LEVEL TOO HIGH»

 Too much foam in the washing machine, spinning has

not been effected. There are two possibilities to solve

the problem:

a) Press the Start button and then interrupt the pro-

gramme by pressing the Quick Wash button several times

until the display «OPEN DOOR» appears.

Mix approx. 30 ml conditioner and approx. 1 litre water.

Start the previously selected wash programme (it may

take several minutes until the machine is released for

the

selection of a new programme). After the water

s upply has been com pleted, switch forward immediately

to «Conditio ning» by pressing the Quick Wash button

and add the conditioner- water mixture into section I of

the detergent drawer. The programme should now end

usually and the spinning process should take place.

After

wards repeat the desired programme, however

with out any detergent.

Press the Start button and then interrupt the pro-

gram me by pressing the Quick Wash button several

times

until the display «OPEN DOOR» appears. Wait for

approx.

1 hour and start the previously selected wash

programme,

move forward immediately to «spinning»

using the Quick

Wash button. Usually the laundry will

be spun. If not, repeat the procedure including waiting

for 1

hour. After wards repeat the desired programme,

however

without any detergent.

X The maximum admissible water level is reached. Wait

until the water has been pumped out completely and

press the Start button. The programme will continue.

«WATER IS BEING PUMPED OUT»

 Too much water is in the washing machine. Water is

pumped off to the set level.

 If you see a lot of foam in the door glass, this means

that too much foam is in the washing machine.

To eliminate this problem proceed as for the error mes-

sage «WATER LEVEL TOO HIGH».

 In future, please reduce the detergent quantity.

If the appliance shows a function fault F – –:

X Stop the programme with the Quick Wash button

and select a new programme.

In the event of repeated error messages:

X Disconnect the electricity for approx. 1 minute and

then switch on again. (Withdraw the mains plug or

switch off the main building switch.)

X The machine is ready to operate once again when the

programme pilot lamps ash.

X Select a new programme.

If the error message still appears:

X Make a note of the error message

X Switch off the water tap and withdraw the mains

plug or switch off the main building switch.

X Inform Customer Service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Novamatic WA6780 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Novamatic WA6780

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info