Bedienungsanleitung Numark CM200 (Seite 3 von 17) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

24743

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

MIXER QUICK SETUP

1. Make sure all items listed on the

front of this guide are included

in the box.

2. READ SAFETY INSTRUCTION

BOOKLET BEFORE USING THE

PRODUCT.

3. Study this setup diagram.

4. Place mixer in an appropriate

position for operation.

5. Make sure all devices are turned

off and all faders and gain knobs

are set to “zero”

6. Connect all stereo input sources

as indicated in the diagram.

7. Connect the stereo outputs to

power amplifier(s), tape decks,

and/or other audio sources.

8. Plug all devices into AC power.

9. Switch everything on in the

following order.

• audio input sources (i.e.

turntables or CD players)

• mixer

• last, any amplifiers or

output devices

10. When turning off, always

reverse this operation by,

• turning off amplifiers

• mixer

• last, any input devices

11. Go to http://www.numark.com

for product registration.

More information about this

product may be found at

http://www.numark.com

REAR CONNECTIONS

1. Phono Inputs: This input is used for connecting

your turntables through the sensitive RIAA phono

preamplifiers. Only turntables with phono level

output should be attached. Line level turntables

must be attached to the line inputs.

2. GND: This screw connector should be used to

secure any turntables or other devices connected

to the mixer that need to be grounded.

3. Line Inputs: CD players, Tape Decks, Samplers

or other line level input devices should be

connected to these inputs.

4. Microphone Input: Microphones with a ¼”

connector can be connected to these input

terminals.

5. Fader Start Connector: to attach your mixer to

a remote start equipped Numark CD player using

industry standard 1/8”(3.5mm) cables.

6. Record Output: This RCA output is for

connecting a recording device such as a tape

deck or CD recorder. The level of the record

output is based upon pre-master levels.

7. Zone Output (RCA): This output is for

connecting an external monitoring device such as

a PA system, powered monitors or a home

stereo. The level of the zone stereo output signal

is controlled by the zone fader.

8. Master Output (RCA): This output is for

connecting an external monitoring device such as

a PA system, powered monitors or a home

stereo. The level of the master stereo output

signal is controlled by the master fader.

9. Stereo Balanced Master Outputs (XLR): low-

impedance XLR type connectors controlled by the

Master fader.

10. AC In: This mixer is designed to work with the

power supply cord that comes with the unit.

While the power is switched off, plug the power

supply into the mixer first, then plug it into the

outlet.

11. Voltage Selector: Set this to the correct voltage

for your location standard.

12. Power Switch: Use this switch to turn on the

mixer after all input devices are already

connected to prevent damage to your equipment.

Turn the mixer on before you turn on amplifiers

and turn of amplifiers before you turn off the

mixer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark CM200 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info