Bedienungsanleitung Numark NDX200 (Seite 4 von 20) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

618157

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

TOP PANEL FEATURES

1. EJECT – Pressing will open or close the

disc tray on the transport. This unit is

designed to play commercially available

CDs and properly burned and finalized

CD-Rs. Due to variances on the

specification of certain CD burners and

CDs, some homemade CDs may not play

properly. We recommend burning CDs at

the minimum speed possible for the best

performance.

2. PLAY / PAUSE – Plays or pauses the

track. Pausing the track will create a cue

point at that location (which can be

adjusted with the JOG WHEEL in Search

Mode).

3. CUE – During playback, pressing CUE will

return to the most recent point where

playback was started and will pause the

track. Holding down CUE will start

playback from this point, and releasing

CUE will cause it to return to that point and

will pause the track. Also, if the track is

paused, you can use the JOG WHEEL to

locate a new cue point.

4. SEARCH – Pressing this button allows

you to use the JOG WHEEL to rapidly

scan through the music. The LED indicator

will be red when Search Mode is active.

(Note: If the JOG WHEEL is not used for

8 seconds, Search Mode will be

deactivated.)

5. JOG WHEEL – The jog wheel serves

many functions depending on its current

mode.

a) If a track is not playing, the JOG

WHEEL will search slowly through a

track's frames. To set a new cue

point, rotate the JOG WHEEL then

begin playback when you have determined the proper position. Press CUE to return to that cue point.

b) If a track is playing, the JOG WHEEL will temporarily bend the pitch of the track. Rotating the JOG WHEEL

clockwise temporarily speeds it up while rotating it counterclockwise slows it down. This is a useful tool for beat-

matching.

c) When the SEARCH button has been activated, rotating the JOG WHEEL will scan rapidly through the track.

6. TRACK KNOB – Turn this knob to select a track to play. Press this knob to skip through your track listing 10 tracks at a

time.

7. PROGRAM – This button helps you create a program – a sequence of tracks to play continuously. To create a

program, press PROGRAM when the CD player is paused. To enter a track into the program, use the TRACK KNOB to

select the desired track then press PROGRAM to enter it. Repeat this process for each track you want to enter (in the

order you want them to play). When you have finished, press PLAY / PAUSE to start playing the program. The tracks

will play in the order you entered them, and "PROGRAM" will be shown on the LCD. To cancel your program as it is

playing, press and hold PROGRAM for 2 seconds so "PROGRAM" disappears from the LCD.

8. SINGLE – Press this button to toggle between Single Play (the deck will stop at the end of each track) or Continuous

Play (the entire disc will be played without interruption).

9. TIME – Switches the time display between elapsed playing time, remaining time on the track, and total remaining time

on the entire CD.

10. LOOP IN – Sets a new cue point or the start point of a loop (a "Loop In" point) during playback.

11. LOOP OUT – Sets the end point of a loop (a "Loop Out" point) and starts playing the loop. While playing a loop, press

LOOP OUT to release it from the loop and continue normal playback.

12. RELOOP – Plays the track immediately from the beginning of a loop (and reactivates the loop).

13. PITCH – Adjusts the range of the PITCH FADER (±4%, 8%, and 16%). The current range will be indicated on the LCD

and by different LEDs.

14. PITCH FADER – The pitch can be changed by pressing the PITCH button so a PITCH LED is lit, then moving the sliding

fader. The pitch will not be changed if the PITCH LED is off.

15. PITCH BEND -/+ – You can use these two pitch bend buttons to temporarily adjust the pitch and tempo of the music up

to -/+ 16% from the current pitch setting.

16. LCD – Indicates all the functions, as they are occurring, with the CD.

10 11 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark NDX200 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info