Bedienungsanleitung Numark NS7 (Seite 7 von 120) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

618120

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

General Controls

1. Displays: Use the screens to view performance information, waveforms, and your library.

See Displays for more information.

2. View: Press this button to cycle through the available NS7III display modes. See Displays

for more information.

3. Shift: Press and hold this button to access secondary functions (in red lettering) of other

controls on NS7III.

4. Touch Mode: Press and hold this button to activate Touch Mode, which lets you access

the touch-capacitive functions of NS7III’s FX 1 Knob, FX 2 Knob, and FX 3 Knob.

Press and hold Shift and then press this button to access the touch-capacitive functions

of the same knobs as above plus the EQ Knobs (Channel Treble, Channel Mid, and

Channel Bass). These functions are momentary, not “latching.”

5. Layer: Selects which Layer in the software is controlled by that hardware Deck. Deck A

can control Layer 1 or 3; Deck B can control Layer 2 or 4.

6. USB Indicator: This LED lights up when NS7III is successfully connected to and

communicating with your computer.

Mixer Controls

7. Input Selector: Set this switch to the desired audio source from this channel: PC (a track

playing on that layer in the software), Mic 2 or Line (a device connected to the Mic 2 Input

or Line Input on NS7III’s rear panel). Please note that the Line/Phono selector switches on

NS7III’s rear panel must also be set properly. Also, a channel’s controls will only send MIDI

information when its Input Selector is set to PC.

Important: Do not set more than one channel’s Input Selectors to Mic2; doing so can

cause unwanted feedback or distortion.

8. Gain Trim: Adjusts the pre-fader, pre-EQ audio level of the corresponding channel in the

software.

9. LED Meters: Monitors the audio levels of the corresponding channel.

10. Channel Treble: Adjusts the high (treble) frequencies. When Touch Mode is activated,

touching this knob will mute the corresponding channel’s high frequencies (an “EQ kill”).

11. Channel Mid: Adjusts the mid-range frequencies. When Touch Mode is activated, touching

this knob will mute the corresponding channel’s mid-range frequencies (an “EQ kill”).

12. Channel Bass: Adjusts the low (bass) frequencies. When Touch Mode is activated,

touching this knob will mute the corresponding channel’s low frequencies (an “EQ kill”).

13. Channel Fader: Adjusts the audio level on the corresponding channel in the software.

14. PFL: Press this button to send this channel’s pre-fader signal to the Cue Channel for

monitoring. When engaged, the button will be lit. By pressing one PFL button at a time, you

will cue that channel alone (and deactivate PFL monitoring for the other channels). To cue to

multiple channels simultaneously, press the PFL buttons for those channels at the same time.

15. Crossfader: Blends audio between the channels assigned to the left and right side of the

crossfader.

16. Master Volume: Adjusts the output volume of the Program Mix.

17. Booth Volume: Adjusts the output volume of the Booth Output mix.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark NS7 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info