Bedienungsanleitung NutriBullet RX (Seite 4 von 15) (Englisch)

703082

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

6 7

SAFETY WARNINGS FOR

EXTRACTING FOR NUTRIBLASTS

• NUTRIBULLET Rx IS PROGRAMMED TO RUN FOR 1 MINUTE DURING

NUTRIBLAST MODE (G BUTTON WILL BE GREEN).

• IF POWER BASE DOES NOT SHUT OFF AFTER 1 MINUTE DURING NUTRIBLAST

CYCLE, STOP IT MANUALLY BY DEPRESSING THE POWER BUTTON, LOCATED

90˚ TO THE LEFT SIDE OF THE G-BUTTON OR SIMPLY LIFT CUP OFF POWER

BASE.

• TO TURN OFF THE MACHINE AT ANYTIME DURING THE NUTRIBLAST CYCLE (G

BUTTON WILL BE GREEN), DEPRESS THE POWER BUTTON, LOCATED 90˚ TO THE

LEFT SIDE OF THE G-BUTTON OR SIMPLY LIFT THE CUP OFF THE POWER BASE.

IF YOU PRESS THE G BUTTON FOR 2 SECONDS DURING EXTRACTION AND THE

LIGHT TURNS RED, YOU ARE IN SOUPERBLASTER MODE. DEPRESS THE POWER

BUTTON, LOCATED 90˚ TO THE LEFT SIDE OF THE G-BUTTON AND SIMPLY LIFT

THE CUP OFF THE POWER BASE TO TURN OFF THE UNIT. THE LIGHT WILL STOP

GLOWING, SIGNIFYING POWER IS OFF. ALWAYS UNPLUG THE POWER BASE UPON

COMPLETION OF PROCESSING.

• DO NOT TOUCH COUPLING GEAR DIRECTLY WITH HANDS AFTER NUTRIBLAST

MODE! THE COUPLING GEAR IN BLADE BASE AND POWER BASE WILL BE HOT!

• DO NOT RUN IN NUTRIBLAST MODE FOR MORE THAN 1 INTERVAL.

• AFTER INITIAL CYCLE, ALLOW POWER BASE TO SHUT OFF COMPLETELY AND

WAIT FOR 15 SECONDS BEFORE STARTING ANOTHER CYCLE.

• DO NOT RUN FOR MORE THAN 3 CONSECUTIVE 1 MINUTE INTERVALS WITHOUT

ALLOWING POWER BASE TO COOL TO PREVENT OVERHEATING AND ALLOW

INGREDIENTS TO SETTLE FOR 2-3 MINUTES AFTER THE 3RD EXTRACTION CYCLE.

• POWER BASE IS EQUIPPED WITH AN INTERNAL THERMAL BREAKER THAT

SHUTS OFF THE POWER BASE IF THE UNIT OVERHEATS.

• IF THE POWER BASE OVERHEATS AND SHUTS OFF, UNPLUG THE POWER

BASE AND PRESS THE POWER BUTTON, LOCATED 90˚ TO THE LEFT OF THE

G-BUTTON AND LET IT COOL FOR AN HOUR OR MORE BEFORE ATTEMPTING

TO USE IT AGAIN. POWER BASE WILL RESET WHEN THE UNIT IS POWERED OFF

AND THE THERMAL BREAKER HAS COOLED DOWN SUFFICIENTLY.

• WHEN MAKING NUT BUTTERS OR OIL-BASED FOODS, DUE TO THE

CONSISTENCY, THE FOOD WILL PROCESS AND THEN STICK TO THE SIDES OF

THE CUP. PROCESS IN 30 SECOND INCREMENTS ONLY BY SIMPLY LIFTING THE

CUP OFF THE POWER BASE BETWEEN INTERVALS. BETWEEN CYCLES, USE A

COMBINATION OF THE TAP METHOD DESCRIBED ON PAGE 19 AND OPEN CUP

AS NEEDED TO SCRAPE DOWN THE INGREDIENTS TO THE CENTER OF THE CUP

BEFORE CONTINUING TO PROCESS IN 30 SECOND INCREMENTS.

• ALLOW MACHINE TO COOL DOWN FOR 10 MIN AFTER 4-5 CYCLES TO PREVENT

OVERHEATING AND DAMAGING THE UNIT.

• To prevent leakage, always align and hand-tighten or use blade remover to tighten the

blade to the NutriBlast Rx cup prior to inverting it and placing the assembly on to the

motor base.

• TO TURN ON THE NUTRIBULLET: Plug the power base into an electrical outlet.

Press the power button, located 90˚ to the left side of the G-button. This will cause

the power button glow BLUE. Next, place the cup blade-side-down onto the power

base. This will activate the NutriBullet Rx’s SMART Technology function, causing the

G-Button at the front of the unit to glow GREEN.

• Once activated, the unit will run for 1 minute in regular NutriBlast Rx mode before it

automatically turns off. The G-button will stop glowing green at the end of the 1-minute

cycle. To turn off completely before the cycle is complete, either lift the cup off of the

base, or press the power button, located 90˚ to the left side of the G-button. The

power button will extend from its recessed position and the blue light will no longer be

lit, signifying the power is off.

• In NutriBlast Rx Mode, the motor will run 2 cycles during the 1 minute interval— ﬁrst

it will slow down half way through the 1 minute interval to allow the ingredients to

settle for improved processing, then it will power-up again for the second half of the

interval. This is a normal function of the NutriBullet Rx.

• Turn the NUTRIBULLET Rx off after each use. Depress the power button, located

90˚ to the left side of the G-button. The BLUE light will stop glowing, signifying

power is off.

POWER OFF INSTRUCTIONS

• To turn off the machine at anytime during the NutriBlast cycle (indicated by the

GREEN glowing G-button), depress the power button, located 90˚ to the left side of

the G-button and simply lift the cup off power base. When the vessel is removed

from the power base, only the GREEN G-button light will turn off. When the power off

button is pressed, the BLUE light will turn off and the blade will stop spinning. To turn

off machine at any time during SouperBlast Mode (indicated by the RED glowing G

button), press the power off button, located 90˚ to the left side of the G-button and

simply lift the SouperBlast Pitcher off the power base. When the vessel is removed

from the power base, only the RED G-button light will turn off. When the power off

button is pressed, the BLUE light will turn off and the blade will stop spinning. Always

press the power off button when machine is not in use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NutriBullet RX Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NutriBullet RX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info