Bedienungsanleitung Octane Fitness RO (Seite 10 von 12) (Englisch)

737868

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

SOFTWARE MANAGEMENT

e console soware includes management functions to help you make the most of your experience with the Octane Rō, including simple

diagnostics to help with troubleshooting and Club (user) settings that may be customized to suit your environment. To access these functions,

press and hold both the Time ( +) and Time ( – ) keys for three seconds, or until you hear a bell. Use the ( + ) key to scroll through the

diagnostics and club setting described below. Press Enter to show the details of a function, to make a change to a user setting, or to run a

diagnostic test. To exit diagnostics, press once or twice Pause Clear until the console resets.

Should you encounter errors or have questions regarding diagnostics, please contact Octane Fitness Customer Service for assistance.

Available options may vary depending upon your software version.

Code

(at the top of the screen

and the center of the tach)

Type Description

diaG nost 1 Diagnostic Firmware. The firmware version, model and console serial number information. Firmware version

number is displayed in the middle of the screen. Model number is displayed in the lower right. The

console serial number is displayed across the lower part of the screen (across several fields). Boot

code version is displayed in the lower left. Press Pause Clear twice to step back to scrolling mode.

diaG nost 2 Diagnostic LCD Display Test. Initiates a sequential illumination of all individual segments of the LCD. Press Pause

Clear twice to step back to scrolling mode.

diaG nost 3 Diagnostic Keypad Test. Press Enter, then press each of the 10 keypad buttons. The name or number of the

pressed button shows on the display and the key counter increments by 1. When all 10 keys have been

successfully tested, “PASS” appears in the display. Press Pause Clear twice to step back to scrolling

mode.

diaG nost 4 Diagnostic Radio Board Communications. The console sends test data to the lower board; “PASS” appears

in the display if return data is received. Radio firmware version and heart rate are displayed in the

lower right and lower left part of the screen. Press Pause Clear twice to step back to scrolling mode.

diaG nost 5 Diagnostic Resistance Level. Move the resistance level all the way forward and back. Level number is displayed

in the Level field, strokes in the middle, and ADC value and RPM in the lower half of the screen. If ADC

is too high or too low, an error displays in the lower half of the screen.

diaG nost 7 Diagnostic Battery. Installed battery and generator volts values are displayed in the lower part of the screen.

Battery state shows near the bottom of the screen; if it is blank or reads “chrg” (charging”, the

battery is good.

CLUB BELL Club Setting Bell Volume. Sets the decibel level of the bell that provides signals during workouts. The options

are Off, 1 (softest), 2 or 3 (loudest), and the default value is 3. Press Enter, then Time ( +) or Time

( – ) keys to scroll through the options. Press Pause Clear once to save your selection and step back

to scrolling mode.

CLUB Brit Club Setting Brightness. Sets the brightness of the display. The default value is 100. Press Enter, then use the

Time ( +) or Time ( – ) keys to increase or decrease the brightness, in 5% increments. Press Pause

Clear once to save your selection and step back to scrolling mode.

USAG U1 R Usage Revolutions. Displays the total number of revolutions for the unit. The data is displayed in thousands,

shown vertically in two groups of three at the lower left of the screen. The display dynamically changes

if you are rowing. If desired, press and hold Quick Start and Pause Clear simultaneously for three

seconds to reset the counter to zero. Press Pause Clear twice to step back to scrolling mode.

USAG U2 St Usage Total Strokes. Displays the total number of strokes for the unit. The data is displayed in thousands,

shown vertically in two groups of three at the lower left of the screen. The display dynamically changes

if you are rowing. If desired, press and hold Quick Start and Pause Clear simultaneously for three

seconds to reset the counter to zero. Press Pause Clear twice to step back to scrolling mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Octane Fitness RO Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Octane Fitness RO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info